參數資料
型號: TLV320AIC29IRGZ
廠商: TEXAS INSTRUMENTS INC
元件分類: 消費家電
英文描述: SPECIALTY CONSUMER CIRCUIT, PQCC48
封裝: 7 X 7 MM, GREEN, PLASTIC, QFN-48
文件頁數: 68/87頁
文件大?。?/td> 1049K
代理商: TLV320AIC29IRGZ
TLV320AIC29
SLAS494B DECEMBER 2005 REVISED OCTOBER 2007
www.ti.com
70
AIC29 Buffer Data Registers (Page 3)
The buffer data registers of the AIC29 hold data results from the SAR ADC conversions in buffer mode. Upon
reset, bit D15 is set to 0, bit D14 is set to 1 and the remaining bits are don’tcare. These registers are read only.
If buffer mode is enabled, then the results of all ADC conversions are placed in the buffer data register. The
data format of the result word (R) of these registers is right-justified which is as follows:
D15
MSB
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
LSB
FUF
EMF
X
ID
R11
MSB
R10
R9
R8
R7
R6
R5
R4
R3
R2
R1
R0
LSB
BIT
NAME
RESET
VALUE
READ/
WRITE
FUNCTION
D15
FUF
0
R
Buffer Full Flag
This flag indicates that all the 64 locations of the buffer are having unread data.
D14
EMF
1
R
Buffer Empty Flag
This flag indicates that there is no unread data available in FIFO. This is generated while reading the
last converted data.
D13
X
R
Reserved
D12
ID
X
R
Data Identification
0 => BAT or AUX2 data in R11R0
1 => AUX1 or TEMP data in R11R0
Order for Writing Data in Buffer When Multiple Inputs are Selected
For Auto Scan Conversion: AUX1 (if selected), AUX2 (if selected), TEMP (if selected)
For Port Scan Conversion: BAT, AUX1, AUX2
D11D0
R11R0
X’s
R
Converted Data
LAYOUT
The following layout suggestions should provide optimum performance from the AIC29. However, many
portable applications have conflicting requirements concerning power, cost, size, and weight. In general, most
portable devices have fairly clean power and grounds because most of the internal components are very low
power. This situation would mean less bypassing for the converter’s power and less concern regarding
grounding. Still, each situation is unique and the following suggestions should be reviewed carefully.
For optimum performance, care should be taken with the physical layout of the AIC29 circuitry. The basic SAR
architecture is sensitive to glitches or sudden changes on the power supply, reference, ground connections,
and digital inputs that occur just prior to latching the output of the analog comparator. Therefore, during any
single conversion for an n-bit SAR converter, there are n windows in which large external transient voltages
can easily affect the conversion result. Such glitches might originate from switching power supplies, nearby
digital logic, and high power devices. The degree of error in the digital output depends on the reference voltage,
layout, and the exact timing of the external event. The error can change if the external event changes in time
with respect to the timing of the critical n windows.
With this in mind, power to the AIC29 should be clean and well bypassed. A 0.1
F ceramic bypass capacitor
should be placed as close to the device as possible. A 1
F to 10 F capacitor may also be needed if the
impedance of the connection between the AIC29 supply pins and system power supply is high.
A 1
F bypass capacitor should be placed on the VREF pin if the SAR ADC is intended to be used with the
internal reference voltage. If an external reference voltage originates from an op amp, make sure that it can
drive any bypass capacitor that is used without oscillation.
The AIC29 architecture offers no inherent rejection of noise or voltage variation in regards to using an external
reference input. This is of particular concern when the reference input is tied to the power supply. Any noise
and ripple from the supply appears directly in the digital results. While high frequency noise can be filtered out,
voltage variation due to line frequency (50 Hz or 60 Hz) can be difficult to remove.
The ground pins should be connected to a clean ground point. In many cases, this is the analog ground. Avoid
connections, which are too near the grounding point of a microcontroller or digital signal processor. If needed,
run a ground trace directly from the converter to the power supply entry or battery connection point. The ideal
layout includes an analog ground plane dedicated to the converter and associated analog circuitry.
相關PDF資料
PDF描述
TLV320AIC3107IYZFR 2 CHANNEL, AUDIO AMPLIFIER, BGA42
TLV320AIC3107IYZFT 2 CHANNEL, AUDIO AMPLIFIER, BGA42
TLV320AIC3107IRSBT 2 CHANNEL, AUDIO AMPLIFIER, PQCC40
TLV320AIC3107IRSBR 2 CHANNEL, AUDIO AMPLIFIER, PQCC40
TLV320AIC3107YZFR 2 CHANNEL, AUDIO AMPLIFIER, PBGA42
相關代理商/技術參數
參數描述
TLV320AIC29IRGZR 功能描述:接口—CODEC Stereo Codec RoHS:否 制造商:Texas Instruments 類型: 分辨率: 轉換速率:48 kSPs 接口類型:I2C ADC 數量:2 DAC 數量:4 工作電源電壓:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-81 封裝:Reel
TLV320AIC29IRGZRG4 功能描述:接口—CODEC Stereo Codec RoHS:否 制造商:Texas Instruments 類型: 分辨率: 轉換速率:48 kSPs 接口類型:I2C ADC 數量:2 DAC 數量:4 工作電源電壓:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-81 封裝:Reel
TLV320AIC29IRGZT 功能描述:接口—CODEC Stereo Codec RoHS:否 制造商:Texas Instruments 類型: 分辨率: 轉換速率:48 kSPs 接口類型:I2C ADC 數量:2 DAC 數量:4 工作電源電壓:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-81 封裝:Reel
TLV320AIC29IRGZTG4 功能描述:接口—CODEC Stereo Codec RoHS:否 制造商:Texas Instruments 類型: 分辨率: 轉換速率:48 kSPs 接口類型:I2C ADC 數量:2 DAC 數量:4 工作電源電壓:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-81 封裝:Reel
TLV320AIC3004IRHBR 制造商:Texas Instruments 功能描述:TISTLV320AIC3004IRHBR LOW-POWER STEREO