參數資料
型號： TLC155
廠商： Electronic Theatre Controls, Inc.
英文描述： EPROM/ROM-Based 8-Bit Microcontroller Series
中文描述： 存儲器/基于ROM的8位微控制器系列
文件頁數： 10/50頁
文件大?。?/td> 552K
代理商： TLC155
2.1.4 STATUS (Status Register)
Address
Name
03h (r/w)
STATUS
This register contains the arithmetic status of the ALU, the RESET status.
If the STATUS Register is the destination for an instruction that affects the Z, DC or C bits, then the write to these
three bits is disabled. These bits are set or cleared according to the device logic. Furthermore, the
TO
and
PD
bits
are not writable. Therefore, the result of an instruction with the STATUS Register as destination may be different
than intended. For example, CLRR STATUS will clear the upper three bits and set the Z bit. This leaves the
STATUS Register as 000u u1uu (where u = unchanged).
C
: Carry/borrow bit.
ADDAR, ADDIA
= 1, a carry occurred.
= 0, a carry did not occur.
SUBAR, SUBIA
= 1, a borrow did not occur.
= 0, a borrow occurred.
Note : A subtraction is executed by adding the two’s complement of the second operand. For rotate (RRR, RLR)
instructions, this bit is loaded with either the high or low order bit of the source register.
DC
: Half carry/half borrow bit.
ADDAR, ADDIA
= 1, a carry from the 4th low order bit of the result occurred.
= 0, a carry from the 4th low order bit of the result did not occur.
SUBAR, SUBIA
= 1, a borrow from the 4th low order bit of the result did not occur.
= 0, a borrow from the 4th low order bit of the result occurred.
Z
:
Zero bit.
= 1, the result of a logic operation is zero.
= 0, the result of a logic operation is not zero.
PD
: Power down flag bit.
= 1, after power-up or by the CLRWDT instruction.
= 0, by the SLEEP instruction.
TO
: Time overflow flag bit.
= 1, after power-up or by the CLRWDT or SLEEP instruction.
= 0, a watch-dog time overflow occurred.
GP2:GP0
: General purpose read/write bits.
2.1.5 FSR (Indirect Data Memory Address Pointer)
Address
Name
B7
B6
B5
04h (r/w)
FSR
RP1
RP0
Bit5:Bit0
: Select registers address in the indirect addressing mode. See 2.1.1 for detail description.
RP1:RP0
: For TLC154/155/156, these bits are not used. Read as “1”s.
For TLC157, these bits are used to switching the bank of four data memory banks. See 2.1.1 for
detail description.
B7
GP2
B6
GP1
B5
GP0
B4
TO
B3
PD
B2
Z
B1
DC
B0
C
B4
Indirect data memory address pointer
B3
B2
B1
B0
TLC
TLC156
Rev0.95 Nov 20, 2003
P.2/TLC156
相關PDF資料
PDF描述
TLC155D EPROM/ROM-Based 8-Bit Microcontroller Series
TLC155M EPROM/ROM-Based 8-Bit Microcontroller Series
TLC155P EPROM/ROM-Based 8-Bit Microcontroller Series
TLC156 EPROM/ROM-Based 8-Bit Microcontroller Series
TLC156D EPROM/ROM-Based 8-Bit Microcontroller Series
相關代理商/技術參數
參數描述
TLC1550 制造商:TI 制造商全稱:Texas Instruments 功能描述:10-BIT ANALOG-TO-DIGITAL CONVERTERS WITH PARALLEL OUTPUTS
TLC1550I 制造商:TI 制造商全稱:Texas Instruments 功能描述:10-BIT ANALOG-TO-DIGITAL CONVERTERS WITH PARALLEL OUTPUTS
TLC1550I_07 制造商:TI 制造商全稱:Texas Instruments 功能描述:10-BIT ANALOG-TO-DIGITAL CONVERTERS WITH PARALLEL OUTPUTS
TLC1550IDW 功能描述:模數轉換器 - ADC LiN-EPIC 10bit A/D RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
TLC1550IDWG4 功能描述:模數轉換器 - ADC 10-Bit 164 kSPS Parallel Out RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*