- 您現在的位置：買賣IC網 > PDF目錄385928 > TLC1541FN (Texas Instruments, Inc.) 10-BIT ANALOG-TO-DIGITAL CONVERTER WITH SERIAL CONTROL AND 11 INPUTS PDF資料下載
參數資料
| 型號： | TLC1541FN |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | 10-BIT ANALOG-TO-DIGITAL CONVERTER WITH SERIAL CONTROL AND 11 INPUTS |
| 中文描述： | 10位模擬到數字與串行控制和11轉換器輸入 |
| 文件頁數： | 9/11頁 |
| 文件大?。?/td> | 161K |
| 代理商： | TLC1541FN |
TLC1541
10-BIT ANALOG-TO-DIGITAL CONVERTER
WITH SERIAL CONTROL AND 11 INPUTS
SLAS073C – DECEMBER 1995 – REVISED AUGUST 1996
9
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
PRINCIPLES OF OPERATION
The TLC1541 is a complete data acquisition system on a single chip. The device includes such functions as sample
and hold, 10-bit A/D converter, data and control registers, and control logic. For flexibility and access speed, there
are four control inputs: chip select (CS), address input, I/O clock, and system clock. These control inputs and a
TTL-compatible, 3-state output are intended for serial communications with a microprocessor or microcomputer. The
TLC1541 can complete conversions in a maximum of 21
μ
s, while complete input-conversion output cycles can be
repeated at a maximum of 31
μ
s.
The system and I/O clocks are normally used independently and do not require any special speed or phase
relationships between them. This independence simplifies the hardware and software control tasks for the device.
Once a clock signal within the specification range is applied to the SYSTEM CLOCK input, the control hardware and
software need only be concerned with addressing the desired analog channel, reading the previous conversion result,
and starting the conversion by using I/O CLOCK. SYSTEM CLOCK drives the conversion-crunching circuitry so that
the control hardware and software need not be concerned with this task.
When CS is high, DATA OUT is in a 3-state condition and ADDRESS INPUT and I/O CLOCK are disabled. This feature
allows each of these terminals, with the exception of the CS terminal, to share a control logic point with its counterpart
terminals on additional A/D devices when using additional TLC1541 devices. In this way, the above feature serves
to minimize the required control logic terminals when using multiple A/D devices.
The control sequence has been designed to minimize the time and effort required to initiate conversion and obtain
the conversion result. A normal control sequence is:
1.
CS is brought low. To minimize errors caused by noise at the CS input, the internal circuitry waits for two
rising edges and then a falling edge of SYSTEM CLOCK after a low CS transition before recognizing the
low transition. This technique protects the device against noise when the device is used in a noisy
environment. The MSB of the previous conversion result automatically appears on DATA OUT.
2.
A new positive-logic multiplexer address shifts in on the first four rising edges of I/O CLOCK. The MSB of
the address shifts in first. The negative edges of these four I/O clock pulses shift out the second, third, fourth,
and fifth most-significant bits of the previous conversion result. The on-chip sample-and-hold begins
sampling the newly addressed analog input after the fourth falling edge. The sampling operation basically
involves the charging of internal capacitors to the level of the analog input voltage.
3.
Five clock cycles are then applied to the I/O CLOCK, and the sixth, seventh, eighth, ninth, and tenth
conversion bits shift out on the negative edges of these clock cycles.
4.
The final tenth-clock cycle is applied to the I/O CLOCK. The falling edge of this clock cycle completes the
analog sampling process and initiates the hold function. Conversion is then performed during the next 44
system clock cycles. After this final I/O clock cycle, CS must go high or the I/O CLOCK must remain low
for at least 44 system-clock cycles to allow for the conversion function.
CS can be kept low during periods of multiple conversion. When keeping CS low during periods of multiple
conversion, special care must be exercised to prevent noise glitches on I/O CLOCK. When glitches occur on I/O
CLOCK, the I/O sequence between the microprocessor/controller and the device loses synchronization. Also, when
CS goes high, it must remain high until the end of the conversion. Otherwise, a valid falling edge of CS causes a reset
condition, which aborts the conversion in progress.
A new conversion may be started and the ongoing conversion simultaneously aborted by performing steps 1 through
4 before the 44 system-clock cycles occur. Such action yields the conversion result of the previous conversion and
not the ongoing conversion.
相關PDF資料 |
PDF描述 |
|---|---|
| TLC1541N | 10-BIT ANALOG-TO-DIGITAL CONVERTER WITH SERIAL CONTROL AND 11 INPUTS |
| TLC1542(中文) | 10-Bit Analog-To-Digital Converters(帶串行控制和11個輸入端的10位模數轉換器) |
| TLC1543(中文) | 10-Bit Analog-To-Digital Converters(帶串行控制和11個輸入端的10位模數轉換器) |
| TLC1549(中文) | 10-Bit Analog-To-Digital Converters(帶串行控制10位模數轉換器) |
| TLC1550(中文) | 10-Bit Analog-To-Digital Converters(10位并行A/D轉換器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TLC1541IDW | 功能描述:模數轉換器 - ADC 10bit A/D w/Ser In RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| TLC1541IDWG4 | 功能描述:模數轉換器 - ADC 10-Bit 32 kSPS Serial Out RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| TLC1541IDWR | 功能描述:模數轉換器 - ADC 10-Bit 32 kSPS Serial Out RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| TLC1541IDWRG4 | 功能描述:模數轉換器 - ADC 10-Bit 32 kSPS Serial Out RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| TLC1541IFN | 功能描述:模數轉換器 - ADC 10bit 11Chl A/D RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。