- 您現在的位置：買賣IC網 > PDF目錄69491 > TL494MJ (TEXAS INSTRUMENTS INC) 0.25 A SWITCHING CONTROLLER, 300 kHz SWITCHING FREQ-MAX, CDIP16 PDF資料下載
參數資料
| 型號： | TL494MJ |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | 0.25 A SWITCHING CONTROLLER, 300 kHz SWITCHING FREQ-MAX, CDIP16 |
| 封裝： | CERAMIC, DIP-16 |
| 文件頁數： | 16/21頁 |
| 文件大?。?/td> | 620K |
| 代理商： | TL494MJ |
www.ti.com
s
+
N
n+1
(xn * X)2
N * 1
Electrical Characteristics
Reference Section
Oscillator Section
Error-Amplifier Section
TL494
PULSE-WIDTH-MODULATION CONTROL CIRCUITS
SLVS074E – JANUARY 1983 – REVISED FEBRUARY 2005
over recommended operating free-air temperature range, VCC = 15 V, f = 10 kHz (unless otherwise noted)
TL494C, TL494I
PARAMETER
TEST CONDITIONS(1)
UNIT
MIN TYP(2)
MAX
Output voltage (REF)
IO = 1 mA
4.75
5
5.25
V
Input regulation
VCC = 7 V to 40 V
2
25
mV
Output regulation
IO = 1 mA to 10 mA
1
15
mV
Output voltage change with temperature
T
A = MIN to MAX
2
10
mV/V
Short-circuit output current(3)
REF = 0 V
25
mA
(1)
For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions.
(2)
All typical values, except for parameter changes with temperature, are at TA = 25°C.
(3)
Duration of short circuit should not exceed one second.
C
TL494C, TL494I
PARAMETER
TEST CONDITIONS(1)
UNIT
MIN TYP(2)
MAX
Frequency
10
kHz
Standard deviation of frequency(3)
All values of VCC, CT, RT, and TA constant
100
Hz/kHz
Frequency change with voltage
VCC = 7 V to 40 V, TA = 25°C
1
Hz/kHz
Frequency change with temperature(4)
T
A = MIN to MAX
10
Hz/kHz
(1)
For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions.
(2)
All typical values, except for parameter changes with temperature, are at TA = 25°C.
(3)
Standard deviation is a measure of the statistical distribution about the mean as derived from the formula:
(4)
Temperature coefficient of timing capacitor and timing resistor are not taken into account.
See Figure 2
TL494C, TL494I
PARAMETER
TEST CONDITIONS
UNIT
MIN TYP(1)
MAX
Input offset voltage
VO (FEEDBACK) = 2.5 V
2
10
mV
Input offset current
VO (FEEDBACK) = 2.5 V
25
250
nA
Input bias current
VO (FEEDBACK) = 2.5 V
0.2
1
A
–0.3 to
Common-mode input voltage range
VCC = 7 V to 40 V
V
VCC – 2
Open-loop voltage amplification
V
O = 3 V, VO = 0.5 V to 3.5 V, RL = 2 k
70
95
dB
Unity-gain bandwidth
VO = 0.5 V to 3.5 V, RL = 2 k
800
kHz
Common-mode rejection ratio
V
O = 40 V, TA = 25°C
65
80
dB
Output sink current (FEEDBACK)
VID = –15 mV to –5 V, V (FEEDBACK) = 0.7 V
0.3
0.7
mA
Output source current (FEEDBACK)
VID = 15 mV to 5 V, V (FEEDBACK) = 3.5 V
–2
mA
(1)
All typical values, except for parameter changes with temperature, are at TA = 25°C.
4
相關PDF資料 |
PDF描述 |
|---|---|
| TL494IN | 0.25 A SWITCHING CONTROLLER, 300 kHz SWITCHING FREQ-MAX, PDIP16 |
| TL494IDG4 | 0.25 A SWITCHING CONTROLLER, 300 kHz SWITCHING FREQ-MAX, PDSO16 |
| TL494INE4 | 0.25 A SWITCHING CONTROLLER, 300 kHz SWITCHING FREQ-MAX, PDIP16 |
| TL494ID | 0.25 A SWITCHING CONTROLLER, 300 kHz SWITCHING FREQ-MAX, PDSO16 |
| TL494CPWE4 | 0.25 A SWITCHING CONTROLLER, 300 kHz SWITCHING FREQ-MAX, PDSO16 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TL494MJB | 制造商:TI 制造商全稱:Texas Instruments 功能描述:PULSE-WIDTH-MODULATION CONTROL CIRCUITS |
| TL494N | 制造商:HTC 制造商全稱:HTC Korea TAEJIN Technology Co. 功能描述:Pulse-Width-Modulation Control Circuits |
| TL494NS | 制造商:TI 制造商全稱:Texas Instruments 功能描述:PULSE-WIDTH-MODULATION CONTROL CIRCUITS |
| TL494PW | 制造商:TI 制造商全稱:Texas Instruments 功能描述:PULSE-WIDTH-MODULATION CONTROL CIRCUITS |
| TL494-S16-R | 制造商:UTC-IC 制造商全稱:UTC-IC 功能描述:VOLTAGE MODE PWM CONTROL CIRCUIT |
發布緊急采購，3分鐘左右您將得到回復。