- 您現在的位置：買賣IC網 > PDF目錄382591 > TL1454YD (Texas Instruments, Inc.) DUAL-CHANNEL PULSE-WIDTH-MODULATION (PWM) CONTROL CIRCUIT PDF資料下載
參數資料
| 型號： | TL1454YD |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | DUAL-CHANNEL PULSE-WIDTH-MODULATION (PWM) CONTROL CIRCUIT |
| 中文描述： | 雙通道脈寬調制（PWM）控制電路 |
| 文件頁數： | 5/24頁 |
| 文件大?。?/td> | 390K |
| 代理商： | TL1454YD |
TL1454, TL1454Y
DUAL-CHANNEL PULSE-WIDTH-MODULATION (PWM)
CONTROL CIRCUIT
SLVS086B – APRIL 1995 – REVISED NOVEMBER 1997
5
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
POST OFFICE BOX 1443
HOUSTON, TEXAS 77251–1443
error amplifier
R1 and R2 should be tight-tolerance (
±
1% or better) devices with low and/or matched temperature coefficients
to minimize output voltage errors. A device with a
±
5% tolerance is suitable for R3.
_
+
IN–
IN+
R2
COMP
To PWM
VO
Compensation
Network
REF
R1
R3
Converter
Output
Figure 2. Sense Divider/Error Amplifier Configuration for Converters with Negative Outputs
Figure 2 shows the divider network and error-amplifier configuration for negative output voltages. In general,
the comments for positive output voltages also apply for negative outputs. The output voltage is given by:
VO
R1Vref
R2
The design procedure for choosing the resistor value is to select a convenient value for R2 (instead of R3 in
the procedure for positive outputs) and calculate R1 and R3 using:
R1
R2VO
Vref
R3
R1R2
R1
R2
Values in the 10-k
to 20-k
range work well for R2. R3 can be omitted and the noninverting amplifier connected
to ground in applications where the output voltage tolerance is not critical.
oscillator
The oscillator frequency can be set between 50 kHz and 2 MHz with a resistor connected between RT and GND
and a capacitor between CT and GND (see Figure 3). Figure 6 is used to determine R
T
and C
T
for the desired
operating frequency. Both components should be tight-tolerance, temperature-stable devices to minimize
frequency deviation. A 1% metal-film resistor is recommended for R
T
, and a 10%, or better, NPO ceramic
capacitor is recommended for C
T
.
RT
CT
RT
2
CT
1
TL1454
Figure 3. Oscillator Timing
相關PDF資料 |
PDF描述 |
|---|---|
| TL1454YN | DUAL-CHANNEL PULSE-WIDTH-MODULATION (PWM) CONTROL CIRCUIT |
| TL1454D | DUAL-CHANNEL PULSE-WIDTH-MODULATION (PWM) CONTROL CIRCUIT |
| TL1454N | DUAL-CHANNEL PULSE-WIDTH-MODULATION (PWM) CONTROL CIRCUIT |
| TL1454Y | DUAL-CHANNEL PULSE-WIDTH-MODULATION (PWM) CONTROL CIRCUIT |
| TL16C2552RHB | 1.8-V to 5-V DUAL UART WITH 16-BYTE FIFOS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TL1454YN | 制造商:TI 制造商全稱:Texas Instruments 功能描述:DUAL-CHANNEL PULSE-WIDTH-MODULATION (PWM) CONTROL CIRCUIT |
| TL1454YPW | 制造商:TI 制造商全稱:Texas Instruments 功能描述:DUAL-CHANNEL PULSE-WIDTH-MODULATION (PWM) CONTROL CIRCUIT |
| TL14617 | 制造商:Distributed By MCM 功能描述:Drill Bit Sharpener |
| TL1464 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:QUAD PULSE-WIDTH-MODULATION CONTROL CIRCUIT |
| TL1464IPT | 功能描述:電壓模式 PWM 控制器 Quad PWM Control Circuit RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。