- 您現在的位置：買賣IC網 > PDF目錄361499 > TK73243MCLH (TOKO Inc.) Cap-Free, NMOS, 150mA Low Dropout Regulator with Reverse Current Protection PDF資料下載
參數資料
| 型號： | TK73243MCLH |
| 廠商： | TOKO Inc. |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | Cap-Free, NMOS, 150mA Low Dropout Regulator with Reverse Current Protection |
| 中文描述： | 無電容，NMOS管，150mA的低壓差穩壓器的反向電流保護 |
| 文件頁數： | 9/16頁 |
| 文件大?。?/td> | 117K |
| 代理商： | TK73243MCLH |
January 1999 TOKO, Inc.
Page 9
TK732xx
DEFINITION AND EXPLANATION OF TECHNICAL TERMS
OUTPUT VOLTAGE (V
OUT
)
The output voltage is specified with V
IN
= (V
OUT(TYP)
+ 1 V)
and I
OUT
= 30 mA.
DROPOUT VOLTAGE (V
DROP
)
The dropout voltage is the difference between the input
voltage and the output voltage at which point the regulator
starts to fall out of regulation. Below this value, the output
voltage will fall as the input voltage is reduced. It is
dependent upon the load current, the external transistor
and the junction temperature.
BASE CONTROL CURRENT (I
BASE
)
The base control current is the drive current for the base of
the external transistor.
OUTPUT CURRENT (I
OUT
)
The output current depends on the characteristics of the
external transistor and current limit setting.
LINE REGULATION (Line Reg)
Line regulation is the ability of the regulator to maintain a
constant output voltage as the input voltage changes. The
line regulation is specified as the input voltage is changed
from V
IN
= V
OUT(TYP)
+ 1 V to V
IN
= V
OUT(TYP)
+ 6 V.
LOAD REGULATION (Load Reg)
Load regulation is the ability of the regulator to maintain a
constant output voltage as the load current changes. It is
a pulsed measurement to minimize temperature effects.
Load regulation depends on the external transistor.
QUIESCENT CURRENT (I
Q
)
The quiescent current is the current which flows through
the ground terminal under no load conditions (I
OUT
= 0 mA)
and excludes the control pin current.
GROUND CURRENT (I
GND
)
Ground current is the current which flows through the
ground pin(s). It is defined as I
IN
- I
OUT
, excluding control
current.
RIPPLE REJECTION RATIO (RR)
Ripple rejection is the ability of the regulator to attenuate
the ripple content of the input voltage at the output. It is
specified with 100 mVrms, 400 Hz superimposed on the
input voltage, where V
IN
= V
OUT(TYP)
+ 1.5 V. The output
decoupling capacitor is set to 10
μ
F, the noise bypass
capacitor is set to 0.1
μ
F, and the load current is set to
30 mA. Ripple rejection is the ratio of the ripple content of
the output vs. the input and is expressed in dB.
STANDBY CURRENT (I
STBY
)
Standby current is the current which flows into the regulator
when the output is turned off by the control function
(V
CONT
= 0 V). It is measured with V
IN
= 8 V (9 V for the
8 V output device).
REMOTE SENSING (V
SENSE
)
The V
SENSE
pin is the output voltage sensing pin. If the
voltage drop to the load caused by the PCB etch resistance
cannot be disregarded, the voltage drop can be
compensated by connecting the V
SENSE
pin as shown
below.
The length of the V
SENSE
etch should be limited to 30 cm
(11.8 in.) maximum.
COLLECTOR
VOUT
EMITTER
BASE
RIPK
CL
TEXTERNAL
TK732XX
相關PDF資料 |
PDF描述 |
|---|---|
| TK73244 | Cap-Free, NMOS, 150mA Low Dropout Regulator with Reverse Current Protection |
| TK73244M | Cap-Free, NMOS, 150mA Low Dropout Regulator with Reverse Current Protection |
| TK73244MCLH | Cap-Free, NMOS, 150mA Low Dropout Regulator with Reverse Current Protection |
| TK73245 | Cap-Free, NMOS, 150mA Low Dropout Regulator with Reverse Current Protection |
| TK73245M | Cap-Free, NMOS, 150mA Low Dropout Regulator with Reverse Current Protection |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TK73243MCLH/43 | 制造商:TOKO 制造商全稱:TOKO, Inc 功能描述:LOW DROPOUT REGULATOR |
| TK73243MILH | 制造商:TOKO 制造商全稱:TOKO, Inc 功能描述:LOW DROPOUT REGULATOR |
| TK73243MILH/43 | 制造商:TOKO 制造商全稱:TOKO, Inc 功能描述:LOW DROPOUT REGULATOR |
| TK73244 | 制造商:TOKO 制造商全稱:TOKO, Inc 功能描述:LOW DROPOUT REGULATOR |
| TK73244M | 制造商:TOKO 制造商全稱:TOKO, Inc 功能描述:LOW DROPOUT REGULATOR |
發布緊急采購，3分鐘左右您將得到回復。