參數資料
型號: TK6593X
廠商: TOKO Inc.
英文描述: LARGE EL LAMP DRIVER
中文描述: 大型發光燈驅動器
文件頁數: 14/16頁
文件大?。?/td> 194K
代理商: TK6593X
Page 14
May 2000 TOKO, Inc.
TK6593x
NOISE CONSIDERATIONS
There are two specific noise types relevant to the user when it comes to choosing EL Drivers: the Audio Noise and the
Electromagnetic Interference (EMI) Noise.
The EMI Noise would most likely come from the boost converter section of the EL Driver circuit. The Toko EL Driver has
specifically been designed to address this issue.
The device runs at a fixed frequency and the frequency is controlled tightly in order to avoid interference.
Furthermore, the panel frequency is forced to be a 128 submultiple of the boost frequency avoiding any type of beating
frequencies.
By choosing shielded coils, the EMI noise problem can further be reduced.
The Audio Noise can come from several components which make up the system.
The coil, if operated in the audio range would be a source of noise. The Toko EL Driver was carefully designed to give
the user the choice of 10 frequencies such that the coil frequency will always be above audio range. Since the device
operates at a fixed frequency in discontinuous conduction mode, there are no possible submultiples which would cause
audible noise.
The filter capacitor can be a source of audio noise. Furthermore, depending on how this cap is mounted, the mounting
can act as an amplifier (as a speaker box). Certain ceramic caps driven from a high voltage source as in the EL Driver
case, demonstrate a PIEZOELECTRIC effect which is distinguishable in the Audio Range.
Other types of caps, such as film type do not denote an audio noise.
The panel itself, being operated well into the Audio Range (175 Hz to 400 Hz) and of a capacitive nature driven from high
voltage may also display Audible Noise. Mounting of this panel can enhance or diminish this natural effect of the panel.
APPLICATION INFORMATION
FIGURE 4: INTENSITY CONTROL APPLICATION
CEL
1C1
D1
EL +
HV
GND
IND
EL -
VCC
L1
Vpower
1.8 to 7 V
R1
R2
3 k
200~ 1 mA sink
3 V ~ 1 mA source
R1 = 1.5 k
R2 = 3.0 k
C2 = 10 nF
1C2
EL LAMP INTENSITY CONTROL APPLICATION
In driving EL lamp panels, it is sometimes desirable to be able to adjust the intensity of the EL lamp. The TK6593x can
be used in such an application. By reducing the voltage supplied to the V
pin of the TK6593x, one can reduce the peak
current regulation point of the IC. This translates into a reduction in the peak to peak output voltage across the EL panel,
which reduces the intensity of the light being emitted from the EL lamp.
By decreasing the input voltage to the V
pin from 2.9 V to 2.1 V, the peak current regulation point will be reduced about
53 mA. This correlates to about a 2/3 reduction in the peak to peak voltage appearing across the EL lamp panel.
The V
pin only takes 200
μ
A max. when the EL driver is in operation. Therefore, it can normally be controlled by logic
power level signals. One way of accomplishing this with two digital logic signals is shown in Figure 4.
相關PDF資料
PDF描述
TK70001 SINGLE INPUT, TWO OUTPUT SOLID STATE SWITCH
TK70001M SINGLE INPUT, TWO OUTPUT SOLID STATE SWITCH
TK70001MCB SINGLE INPUT, TWO OUTPUT SOLID STATE SWITCH
TK70002 SINGLE INPUT, TWO OUTPUT SOLID STATE SWITCH
TK70002MCB SINGLE INPUT, TWO OUTPUT SOLID STATE SWITCH
相關代理商/技術參數
參數描述
TK65A10N1 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:Switching Voltage Regulators
TK65E10N1 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:Switching Voltage Regulators
TK65E10N1,S1X 功能描述:MOSFET 100V N-Ch PWR FET 148A 192W 5400pF RoHS:否 制造商:STMicroelectronics 晶體管極性:N-Channel 汲極/源極擊穿電壓:650 V 閘/源擊穿電壓:25 V 漏極連續電流:130 A 電阻汲極/源極 RDS(導通):0.014 Ohms 配置:Single 最大工作溫度: 安裝風格:Through Hole 封裝 / 箱體:Max247 封裝:Tube
TK65E10N1,S1X(S 制造商:Toshiba America Electronic Components 功能描述:
TK65L60V,VQ(O 制造商:Toshiba America Electronic Components 功能描述: