- 您現在的位置：買賣IC網 > PDF目錄382590 > TISP7350H3SL-S (BOURNS INC) TRIPLE ELEMENT BIDIRECTIONAL THYRISTOR OVERVOLTAGE PROTECTORS PDF資料下載
參數資料
| 型號： | TISP7350H3SL-S |
| 廠商： | BOURNS INC |
| 元件分類： | 浪涌電流限制器 |
| 英文描述： | TRIPLE ELEMENT BIDIRECTIONAL THYRISTOR OVERVOLTAGE PROTECTORS |
| 中文描述： | 350 V, 60 A, SILICON SURGE PROTECTOR |
| 封裝： | ROHS COMPLIANT, PLASTIC, SIP-3 |
| 文件頁數： | 10/13頁 |
| 文件大?。?/td> | 401K |
| 代理商： | TISP7350H3SL-S |
MARCH 1999 - REVISED FEBRUARY 2005
Specifications are subject to change without notice.
Customers should verify actual device performance in their specific applications.
Deployment
These devices are three terminal overvoltage protectors. They limit the voltage between three points in the circuit. Typically, this would be the
two line conductors and protective ground (Figure 11).
TISP7xxxH3SL Overvoltage Protector Series
APPLICATIONS INFORMATION
Impulse Testing
To verify the withstand capability and safety of the equipment, standards require that the equipment is tested with various impulse wave forms.
The table below shows some common values.
In Figure 11, protectors Th2 and Th3 limit the maximum voltage between each conductor and ground to the
±
V(BO) of the individual protector.
Protector Th1 limits the maximum voltage between the two conductors to its
±
V(BO) value.
Manufacturers are being increasingly required to design in protection coordination. This means that each protector is operated at its design
level and currents are diverted through the appropriate protector, e.g. the primary level current through the primary protector and lower levels
of current may be diverted through the secondary or inherent equipment protection. Without coordination, primary level currents could pass
through the equipment only designed to pass secondary level currents. To ensure coordination happens with fixed voltage protectors, some
resistance is normally used between the primary and secondary protection. The values given in this data sheet apply to a 400 V (d.c.
sparkover) gas discharge tube primary protector and the appropriate test voltage when the equipment is tested with a primary protector.
If the impulse generator current exceeds the protector’s current rating, then a series resistance can be used to reduce the current to the
protector’s rated value to prevent possible failure. The required value of series resistance for a given waveform is given by the following
calculations. First, the minimum total circuit impedance is found by dividing the impulse generator’s peak voltage by the protector’s rated
current. The impulse generator’s fictive impedance (generator’s peak voltage divided by peak short circuit current) is then subtracted from the
minimum total circuit impedance to give the required value of series resistance. In some cases, the equipment will require verification over a
temperature range. By using the rated waveform values from Figure 10, the appropriate series resistor value can be calculated for ambient
temperatures in the range of -40
°
C to 85
°
C.
Figure 11. MULTI-POINT PROTECTION
Th3
Th2
Th1
Standard
Peak Voltage
Setting
V
Voltage
Waveform
μ
s
2/10
10/1000
10/160
10/560
9/720
(SINGLE)
(DUAL)
0.5/700
10/700
(SINGLE)
(SINGLE)
(DUAL)
Peak Current
Value
A
Current
Waveform
μ
s
2/10
10/1000
10/160
10/560
5/320
5/320
4/250
0.2/310
5/310
5/310
5/310
4/250
TISP7xxxH3
25
°
C Rating
A
Series
Resistance
Coordination
Resistance
(Min.)
GR-1089-CORE
2500
1000
1500
800
1000
1500
1500
1500
1000
1500
4000
4000
500
100
200
100
25
37.5
2 x 27
37.5
25
37.5
100
2 x 72
500
100
250
130
200
200
2 x 225
200
200
200
200
2 x 225
0
NA
FCC Part 68
(March 1998)
0
NA
I 31-24
0
NA
NA
NA
4.5
6.0
ITU-T K.20/K.21
0
FCC Part 68 terminology for the waveforms produced by the ITU-T recommendation K.21 10/700 impulse generator
NA = Not Applicable, primary protection removed or not specified.
相關PDF資料 |
PDF描述 |
|---|---|
| TISP7400H3SL-S | TRIPLE ELEMENT BIDIRECTIONAL THYRISTOR OVERVOLTAGE PROTECTORS |
| TISP7XXXH3SL | TRIPLE ELEMENT BIDIRECTIONAL THYRISTOR OVERVOLTAGE PROTECTORS |
| TISP7070H3SL-S | TRIPLE ELEMENT BIDIRECTIONAL THYRISTOR OVERVOLTAGE PROTECTORS |
| TISP7080H3SL | TRIPLE ELEMENT BIDIRECTIONAL THYRISTOR OVERVOLTAGE PROTECTORS |
| TISP7080H3SL-S | TRIPLE ELEMENT BIDIRECTIONAL THYRISTOR OVERVOLTAGE PROTECTORS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TISP73580H3SL | 功能描述:硅對稱二端開關元件 275V 600mA RoHS:否 制造商:Bourns 轉折電流 VBO:40 V 最大轉折電流 IBO:800 mA 不重復通態電流: 額定重復關閉狀態電壓 VDRM:25 V 關閉狀態漏泄電流（在 VDRM IDRM 下）: 保持電流（Ih 最大值）:50 mA 開啟狀態電壓:5 V 關閉狀態電容 CO:120 pF 最大工作溫度:+ 150 C 安裝風格:SMD/SMT 封裝 / 箱體:DO-214AA |
| TISP7360F3DR | 功能描述:硅對稱二端開關元件 RoHS:否 制造商:Bourns 轉折電流 VBO:40 V 最大轉折電流 IBO:800 mA 不重復通態電流: 額定重復關閉狀態電壓 VDRM:25 V 關閉狀態漏泄電流（在 VDRM IDRM 下）: 保持電流（Ih 最大值）:50 mA 開啟狀態電壓:5 V 關閉狀態電容 CO:120 pF 最大工作溫度:+ 150 C 安裝風格:SMD/SMT 封裝 / 箱體:DO-214AA |
| TISP7360F3DR-S | 功能描述:硅對稱二端開關元件 RoHS:否 制造商:Bourns 轉折電流 VBO:40 V 最大轉折電流 IBO:800 mA 不重復通態電流: 額定重復關閉狀態電壓 VDRM:25 V 關閉狀態漏泄電流（在 VDRM IDRM 下）: 保持電流（Ih 最大值）:50 mA 開啟狀態電壓:5 V 關閉狀態電容 CO:120 pF 最大工作溫度:+ 150 C 安裝風格:SMD/SMT 封裝 / 箱體:DO-214AA |
| TISP7360F3P | 功能描述:硅對稱二端開關元件 RoHS:否 制造商:Bourns 轉折電流 VBO:40 V 最大轉折電流 IBO:800 mA 不重復通態電流: 額定重復關閉狀態電壓 VDRM:25 V 關閉狀態漏泄電流（在 VDRM IDRM 下）: 保持電流（Ih 最大值）:50 mA 開啟狀態電壓:5 V 關閉狀態電容 CO:120 pF 最大工作溫度:+ 150 C 安裝風格:SMD/SMT 封裝 / 箱體:DO-214AA |
| TISP7360F3P-S | 功能描述:硅對稱二端開關元件 RoHS:否 制造商:Bourns 轉折電流 VBO:40 V 最大轉折電流 IBO:800 mA 不重復通態電流: 額定重復關閉狀態電壓 VDRM:25 V 關閉狀態漏泄電流（在 VDRM IDRM 下）: 保持電流（Ih 最大值）:50 mA 開啟狀態電壓:5 V 關閉狀態電容 CO:120 pF 最大工作溫度:+ 150 C 安裝風格:SMD/SMT 封裝 / 箱體:DO-214AA |
發布緊急采購，3分鐘左右您將得到回復。