- 您現在的位置：買賣IC網 > PDF目錄383996 > THS4082DGN (Texas Instruments, Inc.) 175-MHz LOW-POWER HIGH-SPEED AMPLIFIERS PDF資料下載
參數資料
| 型號： | THS4082DGN |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | 175-MHz LOW-POWER HIGH-SPEED AMPLIFIERS |
| 中文描述： | 175 - MHz的低功耗高速放大器 |
| 文件頁數： | 17/24頁 |
| 文件大?。?/td> | 384K |
| 代理商： | THS4082DGN |
THS4081, THS4082
175-MHz LOW-POWER HIGH-SPEED AMPLIFIERS
SLOS274C – DECEMBER 1999 – REVISED MAY 2000
17
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
APPLICATION INFORMATION
general PowerPAD
design considerations (continued)
Although there are many ways to properly heatsink this device, the following steps illustrate the recommended
approach.
Thermal pad area (68 mils x 70 mils) with 5 vias
(Via diameter = 13 mils)
Figure 45. PowerPAD PCB Etch and Via Pattern
1.
Prepare the PCB with a top side etch pattern as shown in Figure 45. There should be etch for the leads as
well as etch for the thermal pad.
2.
Place five holes in the area of the thermal pad. These holes should be 13 mils in diameter. Keep them small
so that solder wicking through the holes is not a problem during reflow.
3.
Additional vias may be placed anywhere along the thermal plane outside of the thermal pad area. This helps
dissipate the heat generated by the THS408xDGN IC. These additional vias may be larger than the 13-mil
diameter vias directly under the thermal pad. They can be larger because they are not in the thermal pad
area to be soldered, so wicking is not a problem.
4.
Connect all holes to the internal ground plane.
5.
When connecting these holes to the ground plane, do
notuse the typical web or spoke via connection
methodology. Web connections have a high thermal resistance connection that is useful for slowing the heat
transfer during soldering operations. This makes the soldering of vias that have plane connections easier.
In this application, however, low thermal resistance is desired for the most efficient heat transfer. Therefore,
the holes under the THS408xDGN package should make their connection to the internal ground plane with
a complete connection around the entire circumference of the plated-through hole.
6.
The top-side solder mask should leave the terminals of the package and the thermal pad area with its five
holes exposed. The bottom-side solder mask should cover the five holes of the thermal pad area. This
prevents solder from being pulled away from the thermal pad area during the reflow process.
7.
Apply solder paste to the exposed thermal pad area and all of the IC terminals.
8.
With these preparatory steps in place, the THS408xDGN IC is simply placed in position and run through
the solder reflow operation as any standard surface-mount component. This results in a part that is properly
installed.
相關PDF資料 |
PDF描述 |
|---|---|
| THS4082EVM | 175-MHz LOW-POWER HIGH-SPEED AMPLIFIERS |
| THS4081D | 175-MHz LOW-POWER HIGH-SPEED AMPLIFIERS |
| THS4081DGN | 175-MHz LOW-POWER HIGH-SPEED AMPLIFIERS |
| THS4081EVM | 175-MHz LOW-POWER HIGH-SPEED AMPLIFIERS |
| THS4130EVM | HIGH SPEED LOW NOISE, FULLY DIFFERENTIAL I/O AMPLIFIERS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| THS4082EVM | 功能描述:放大器 IC 開發工具 THS4082 175MHz Lo-Po Hi-Spd Amp Eval Bd RoHS:否 制造商:International Rectifier 產品:Demonstration Boards 類型:Power Amplifiers 工具用于評估:IR4302 工作電源電壓:13 V to 23 V |
| THS4082ID | 功能描述:高速運算放大器 Dual 175MHz RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| THS4082IDG4 | 功能描述:高速運算放大器 175-MHz Low-Power Vltg-Feedback Dual RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| THS4082IDGN | 功能描述:高速運算放大器 175-MHz Low-Power Vltg-Feedback Dual RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| THS4082IDGNG4 | 功能描述:高速運算放大器 175-MHz Low-Power Vltg-Feedback Dual RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。