參數資料
型號： THS4032CDGNRG4
廠商： Texas Instruments
文件頁數： 21/47頁
文件大?。?/td> 0K
描述： IC OPAMP VFB 100MHZ DUAL 8MSOP
標準包裝： 2,500
放大器類型： 電壓反饋
電路數： 2
轉換速率： 100 V/µs
-3db帶寬： 100MHz
電流 - 輸入偏壓： 3µA
電壓 - 輸入偏移： 500µV
電流 - 電源： 8.5mA
電流 - 輸出 / 通道： 90mA
電壓 - 電源，單路/雙路(±)： 9 V ~ 32 V，±4.5 V ~ 16 V
工作溫度： 0°C ~ 70°C
安裝類型： 表面貼裝
封裝/外殼： 8-TSSOP，8-MSOP（0.118"，3.00mm 寬）裸露焊盤
供應商設備封裝： 8-MSOP-PowerPad
包裝： 帶卷 (TR)
配用： 296-10031-ND - EVAL MOD FOR THS4032
DIE
Side View (a)
End View (b)
Bottom View (c)
DIE
Thermal
Pad
SLOS224G – JULY 1999 – REVISED MARCH 2010
www.ti.com
CIRCUIT-LAYOUT CONSIDERATIONS
In order to achieve the levels of high-frequency performance of the THS403x, it is essential that proper
printed-circuit board (PCB) high-frequency design techniques be followed. A general set of guidelines is given
below. In addition, a THS403x evaluation board is available to use as a guide for layout or for evaluating the
device performance.
Ground planes: It is highly recommended that a ground plane be used on the board to provide all
components with a low inductive ground connection. However, in the areas of the amplifier inputs and output,
the ground plane can be removed to minimize the stray capacitance.
Proper power-supply decoupling: Use a 6.8-mF tantalum capacitor in parallel with a 0.1-mF ceramic capacitor
on each supply terminal. It may be possible to share the tantalum among several amplifiers depending on the
application, but a 0.1-mF ceramic capacitor should always be used on the supply terminal of every amplifier.
In addition, the 0.1-mF capacitor should be placed as close as possible to the supply terminal. As this distance
increases, the inductance in the connecting trace makes the capacitor less effective. The designer should
strive for distances of less than 0.1 inch between the device power terminals and the ceramic capacitors.
Sockets: Sockets are not recommended for high-speed operational amplifiers. The additional lead inductance
in the socket pins will often lead to stability problems. Surface-mount packages soldered directly to the
printed-circuit board is the best implementation.
Short trace runs/compact part placements: Optimum high-frequency performance is achieved when stray
series inductance has been minimized. To realize this, the circuit layout should be made as compact as
possible, thereby minimizing the length of all trace runs. Particular attention should be paid to the inverting
input of the amplifier. Its length should be kept as short as possible. This will help to minimize stray
capacitance at the input of the amplifier.
Surface-mount passive components: Using surface-mount passive components is recommended for
high-frequency amplifier circuits for several reasons. First, because of the extremely low lead inductance of
surface-mount components, the problem with stray series inductance is greatly reduced. Second, the small
size of surface-mount components naturally leads to a more compact layout thereby minimizing both stray
inductance and capacitance. If leaded components are used, it is recommended that the lead lengths be kept
as short as possible.
GENERAL PowerPAD DESIGN CONSIDERATIONS
The THS403x is available in a thermally-enhanced DGN package, which is a member of the PowerPAD family of
packages. This package is constructed using a downset leadframe upon which the die is mounted [see
Figure 60(a) and Figure 60(b)]. This arrangement results in the leadframe being exposed as a thermal pad on
the underside of the package [see Figure 60(c)]. Because this thermal pad has direct thermal contact with the
die, excellent thermal performance can be achieved by providing a good thermal path away from the thermal
pad.
The PowerPAD package allows for both assembly and thermal management in one manufacturing operation.
During the surface-mount solder operation (when the leads are being soldered), the thermal pad can also be
soldered to a copper area underneath the package. Through the use of thermal paths within this copper area,
heat can be conducted away from the package into either a ground plane or other heat-dissipating device.
The PowerPAD package represents a breakthrough in combining the small area and ease of assembly of
surface mount with the heretofore awkward mechanical methods of heatsinking.
A.
The thermal pad is electrically isolated from all terminals in the package.
Figure 60. Views of Thermally-Enhanced DGN Package
28
Copyright 1999–2010, Texas Instruments Incorporated
Product Folder Link(s): THS4031 THS4032
相關PDF資料
PDF描述
AD8601WARTZ-R7 IC AMP GP R-R I/O SGL SOT23-5
52062-302LF METRAL REC PF SG CNR LF
MMA21-009 CONN RACK/PANEL 9POS 5A
ADA4850-2YCPZ-RL IC OPAMP VF R-R DUAL 16LFCSP
TSW-144-05-L-D CONN HEADER 88POS .100" DL GOLD
相關代理商/技術參數
參數描述
THS4032CDR 功能描述:高速運算放大器 100-MHz Low Noise Vltg-Feedback Dual RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube
THS4032CDRG4 功能描述:高速運算放大器 100-MHz Low Noise Vltg-Feedback Dual RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube
THS4032D 制造商:TI 制造商全稱:Texas Instruments 功能描述:100-MHz LOW-NOISE HIGH-SPEED AMPLIFIERS
THS4032DGN 制造商:TI 制造商全稱:Texas Instruments 功能描述:100-MHz LOW-NOISE HIGH-SPEED AMPLIFIERS
THS4032-EP 制造商:TI 制造商全稱:Texas Instruments 功能描述:100-MHz LOW-NOISE HIGH-SPEED AMPLIFIERS
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*