- 您現(xiàn)在的位置：買賣IC網 > PDF目錄373629 > TEA2261 (意法半導體) Switch Mode Power Supply Controller(開關模式電源控制器) PDF資料下載
參數資料
| 型號： | TEA2261 |
| 廠商： | 意法半導體 |
| 英文描述： | Switch Mode Power Supply Controller(開關模式電源控制器) |
| 中文描述： | 開關電源控制器（開關模式電源控制器） |
| 文件頁數： | 5/9頁 |
| 文件大?。?/td> | 120K |
| 代理商： | TEA2261 |
GENERAL DESCRIPTION
The TEA2260/61 is an off-line switch mode power
supply controller. The synchronization function and
the specific operation in stand-by mode make it well
adapted to video applications such as TV sets,
VCRs, monitors, etc...
The TEA2260/61 can be used in two types of
architectures :
- Master/slave architecture. In this case, the
TEA2260/61 drives the power transistor accord-
ing to the pulse width modulated signals gener-
ated by the secondary located master circuit. A
pulse transformer provides the feedback (see
Figure 1).
- Conventional architecture with linear feedback
signal (feedback sources : optocoupler or trans-
former winding) (see Figure 2).
Using the TEA2260/61, the stand-by auxiliary
power supply, often realized with a small but costly
50Hz transformer, is no longer necessary. The
burst mode operation of the TEA2260/61 makes
possible the control of very low output power (down
to less than 1W) with the main power transformer.
When used in a master/slave architecture, the
TEA2260/61 and also the power transistor turn-off
can be easily synchronized with the line trans-
former. The switching noise cannot disturb the
picture in this case.
As an S.M.P.S. controller, the TEA2260/61 features
the following functions :
- Power supply start-up (with soft-start)
- PWM generator
- Direct power transistor drive (+1.2A, -2.0A)
- Safety functions : pulse by pulse current limita-
tion, output power limitation, over and under volt-
age lock-out.
S.M.P.S. OPERATING DESCRIPTION
Starting Mode - Stand By Mode
Power for circuit supply is taken from the mains
through a high value resistor before starting. As
long as V
CC
of the TEA2260/61 is below V
CC
start,
the quiescent current is very low (typically 0.7mA)
and the electrolytic capacitor across V
CC
is linearly
charged. When V
CC
reaches V
CC
start (typically
10.3V), the circuit starts, generating output pulses
with a soft-starting. Then the SMPS goes into the
stand-by mode and the output voltage is a percen-
tage of the nominal output voltage (eg. 80%).
For this the TEA2260/61 contains all the functions
required for primary mode regulation : a fixed fre-
quency oscillator, a voltage reference, an error
amplifier and a pulse width modulator (PWM).
For transmission of low power with a good effi-
ciency in stand-by, an automatic burst generation
system is used, in order to avoid audible noise.
Normal Mode (secondary regulation)
The normal operating of the TV set is obtained by
sending to the TEA2260/61 regulation pulses gen-
erated by a regulator located in the secondary side
of the power supply.
This architecture uses the "Master-slave Concept",
advantages of which are now well-known espe-
cially the very high efficiency in stand-by mode, and
the accurate regulation in normal mode.
Stand-by mode or normal mode are obtained by
supplying or not the secondary regulator. This can
be ordonnered for exemple by a microprocessor in
relation with the remote control unit.
Regulation pulses are applied to the TEA2260/61
through a small pulse-transformer to the IN input
(Pin 2). This input is sensitive to positive square
pulses. The typical threshold of this input is 0.85V.
The frequency of pulses coming from the secon-
dary regulator can be lower or higher than the
frequency of the starting oscillator.
The TEA2260/61 has no soft-starting system when
it receives pulses from the secondary. The soft-
starting has to be located in the secondary regula-
tor.
Due to the principle of the primary regulation,
pulses generated by the starting system automat-
ically disappear when the voltage delivered by the
SMPS increases.
Stand-by Mode - Normal Mode Transition
During the transition there are simultaneously
pulses coming from the primary and secondary
regulators.
These signals are not synchronized and some care
has to be taken to ensure the safety of the switching
power transistor.
A very sure and simple way consist in checking the
transformer demagnetization state.
- A primary pulse is taken in account only if the
transformer is demagnetized after a conduction
of the power transistor required by the secondary
regulator.
- A secondary pulse is taken in account only if the
transformer is demagnetized after a conduction
of the power transistor required by the primary
regulator.
With this arrangement the switching safety area of
the power transistor is respected and there is no
risk of transformer magnetization.
The magnetization state of the transformer is
checked by sensing the voltage across a winding
of the transformer (generally the same which sup-
plies the TEA2261). This is made by connecting a
resistor between this winding and the demagneti-
zation sensing input of the circuit (Pin 1).
TEA2260 - TEA2261
5/9
相關PDF資料 |
PDF描述 |
|---|---|
| TEA2262 | Switch Mode Power Supply Controller(開關模式電源控制器) |
| TEA3717 | STEPPER MOTOR DRIVER |
| TEA3717DP | STEPPER MOTOR DRIVER |
| TEA3718 | STEPPER MOTOR DRIVER |
| TEA3718DP | STEPPER MOTOR DRIVER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TEA2261_03 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:SWITCH MODE POWER SUPPLY CONTROLLER |
| TEA2262 | 功能描述:電流型 PWM 控制器 SMPS Controller RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| TEA2R2M1CTR-0512P | 功能描述:鋁質電解電容器 - 帶引線 16V 2.2uF 20% RoHS:否 制造商:Kemet 引線類型: 電容:220 uF 容差:20 % 電壓額定值:25 V 工作溫度范圍: 端接類型:Radial 外殼直徑:8 mm 外殼長度:11 mm 引線間隔:5 mm 產品:General Purpose Electrolytic Capacitors 封裝:Bulk |
| TEA2R2M1HBK-0512P | 功能描述:鋁質電解電容器 - 帶引線 50V 2.2uF 20% RoHS:否 制造商:Kemet 引線類型: 電容:220 uF 容差:20 % 電壓額定值:25 V 工作溫度范圍: 端接類型:Radial 外殼直徑:8 mm 外殼長度:11 mm 引線間隔:5 mm 產品:General Purpose Electrolytic Capacitors 封裝:Bulk |
| TEA2R2M1HBK-0512S | 制造商:Surge Components Inc 功能描述:CAP ALUM 2.2UF 50V ?20% 2000LHRS 5 X 12 - Bulk |
發(fā)布緊急采購，3分鐘左右您將得到回復。