- 您現在的位置：買賣IC網 > PDF目錄371183 > TDA8924 (NXP Semiconductors N.V.) 2 x 120 W class-D power amplifier PDF資料下載
參數資料
| 型號： | TDA8924 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | 2 x 120 W class-D power amplifier |
| 中文描述： | 2 × 120瓦D類功率放大器 |
| 文件頁數： | 32/35頁 |
| 文件大小： | 722K |
| 代理商： | TDA8924 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁當前第32頁第33頁第34頁第35頁
2003 Jul 28
32
Philips Semiconductors
Objective specification
2
×
120 W class-D power amplifier
TDA8924
18 SOLDERING
18.1
Introduction to soldering surface mount
packages
Thistextgivesaverybriefinsighttoacomplextechnology.
A more in-depth account of soldering ICs can be found in
our “Data Handbook IC26; Integrated Circuit Packages”
(document order number 9398 652 90011).
There is no soldering method that is ideal for all surface
mount IC packages. Wave soldering can still be used for
certainsurfacemountICs,butitisnotsuitableforfinepitch
SMDs. In these situations reflow soldering is
recommended.
18.2
Reflow soldering
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
Driven by legislation and environmental forces the
worldwide use of lead-free solder pastes is increasing.
Several methods exist for reflowing; for example,
convection or convection/infrared heating in a conveyor
type oven. Throughput times (preheating, soldering and
cooling) vary between 100 and 200 seconds depending
on heating method.
Typical reflow peak temperatures range from
215 to 270
°
C depending on solder paste material. The
top-surface temperature of the packages should
preferably be kept:
below 220
°
C (SnPb process) or below 245
°
C (Pb-free
process)
– for all BGA and SSOP-T packages
– for packages with a thickness
≥
2.5 mm
– for packages with a thickness < 2.5 mm and a
volume
≥
350 mm
3
so called thick/large packages.
below 235
°
C (SnPb process) or below 260
°
C (Pb-free
process) for packages with a thickness < 2.5 mm and a
volume < 350 mm
3
so called small/thin packages.
Moisture sensitivity precautions, as indicated on packing,
must be respected at all times.
18.3
Wave soldering
Conventional single wave soldering is not recommended
forsurfacemountdevices(SMDs)orprinted-circuitboards
with a high component density, as solder bridging and
non-wetting can present major problems.
To overcome these problems the double-wave soldering
method was specifically developed.
If wave soldering is used the following conditions must be
observed for optimal results:
Use a double-wave soldering method comprising a
turbulent wave with high upward pressure followed by a
smooth laminar wave.
For packages with leads on two sides and a pitch (e):
– larger than or equal to 1.27 mm, the footprint
longitudinal axis is
preferred
to be parallel to the
transport direction of the printed-circuit board;
– smaller than 1.27 mm, the footprint longitudinal axis
must
be parallel to the transport direction of the
printed-circuit board.
The footprint must incorporate solder thieves at the
downstream end.
Forpackageswithleadsonfoursides,thefootprintmust
be placed at a 45
°
angle to the transport direction of the
printed-circuit board. The footprint must incorporate
solder thieves downstream and at the side corners.
During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the
adhesive is cured.
Typical dwell time of the leads in the wave ranges from
3 to 4 seconds at 250
°
C or 265
°
C, depending on solder
material applied, SnPb or Pb-free respectively.
A mildly-activated flux will eliminate the need for removal
of corrosive residues in most applications.
18.4
Manual soldering
Fix the component by first soldering two
diagonally-opposite end leads. Use a low voltage (24 V or
less) soldering iron applied to the flat part of the lead.
Contact time must be limited to 10 seconds at up to
300
°
C.
When using a dedicated tool, all other leads can be
soldered in one operation within 2 to 5 seconds between
270 and 320
°
C.
相關PDF資料 |
PDF描述 |
|---|---|
| TDA8924TH | 2 x 120 W class-D power amplifier |
| TDA8925 | Power stage 2 x 15 to 25Wclass-D audio amplifier |
| TDA8925J | Power stage 2 x 15 to 25Wclass-D audio amplifier |
| TDA8925ST | Power stage 2 x 15 to 25Wclass-D audio amplifier |
| TDA8939 | Zero dead time Class-D 7.5 A power comparator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TDA8924TH | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:2 x 120 W class-D power amplifier |
| TDA8924TH/N2,118 | 功能描述:IC AMP AUDIO PWR 240W D 24HSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:H 類 輸出類型:耳機，2-通道（立體聲） 在某負載時最大輸出功率 x 通道數量:35mW x 2 @ 16 歐姆 電源電壓:1.62 V ~ 1.98 V 特點:I²C，麥克風，靜音，短路保護，音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP（2.09x2.09） 封裝/外殼:25-WFBGA，WLCSP 包裝:帶卷 (TR) |
| TDA8925 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Power stage 2 x 15 to 25Wclass-D audio amplifier |
| TDA8925J | 制造商:Panasonic Industrial Company 功能描述:IC |
| TDA8925J/N1,112 | 功能描述:IC AMP AUDIO PWR 20W STER 17SIL RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:H 類 輸出類型:耳機，2-通道（立體聲） 在某負載時最大輸出功率 x 通道數量:35mW x 2 @ 16 歐姆 電源電壓:1.62 V ~ 1.98 V 特點:I²C，麥克風，靜音，短路保護，音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP（2.09x2.09） 封裝/外殼:25-WFBGA，WLCSP 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。