參數資料
型號： TDA8589J
廠商： NXP SEMICONDUCTORS
元件分類： 消費家電
英文描述： I2C-bus controlled 4 45 Watt power amplifier and multiple voltage regulator
中文描述： SPECIALTY CONSUMER CIRCUIT, PZFM37
封裝： PLASTIC, SOT725-1, 37 PIN
文件頁數： 8/55頁
文件大?。?/td> 561K
代理商： TDA8589J
2004 Feb 24
8
Philips Semiconductors
Product speci
cation
I
2
C-bus controlled 4 45 Watt power
ampli
er and multiple voltage regulator
TDA8589J; TDA8589xJ
FUNCTIONAL DESCRIPTION
The TDA8589 is a multiple voltage regulator combined
with fourindependent audio power amplifiers configured in
bridge tied load with diagnostic capability. The output
voltages of all regulators except regulators 2 and 3 can be
controlled via the I
2
C-bus.However, regulator 3 can be set
to 0 V via the I
2
C-bus. The output voltage of regulator 2
(microcontroller supply) and the maximum output voltage
of regulator 3 (mechanical digital and microcontroller
supplies) can both be either 5 V or 3.3 V depending on the
type number. The maximum output voltages of both
regulators are fixed to avoid any risk of damaging the
microcontroller that may occur during a disturbance of the
I
2
C-bus.
The amplifier diagnostic functions give information about
output offset, load, or short-circuit. Diagnostic functions
are controlled via the I
2
C-bus. The TDA8589 is protected
against short-circuit, over-temperature, open ground and
open V
P
connections. If a short-circuit occurs at the input
or output of a single amplifier, that channel shuts down,
and the other channels continue to operate normally. The
channel that has a short-circuit can be disabled by the
microcontroller via the appropriate enable bit of the
I
2
C-bus to prevent any noise generated by the fault
condition from being heard.
Start-up
At power on, regulator 2 will reach its final voltage when
thebackup capacitorvoltage exceeds5.5 Vindependently
of the voltage on pin STB. When pin STBis LOW, the total
quiescent current is low, and the I
2
C-bus lines are high
impedance.
When pin STB is HIGH, the I
2
C-bus is biased on and then
the TDA8589 performs a power-on reset. When bit D0 of
instruction byte IB1 is set, the amplifier is activated, bit D7
of data byte 2 (power-on reset occurred) is reset, and
pin DIAG is no longer held LOW.
Start-up and shut-down timing
(see Fig.12)
Acapacitorconnected to pin SVRenablessmoothstart-up
and shut-down, preventing the amplifier from producing
audible clicks at switch-on or switch-off. The start-up and
shut-down times can be extended by increasing the
capacitor value.
If the amplifier is shut down using pin STB, the amplifier is
muted, the regulators and switches are switched off, and
the capacitor connected to pin SVR discharges. The low
currentstandby modeisactivated2 seconds afterpin STB
goes LOW.
Power-on reset and supply voltage spikes
(see Fig.13
and (see Fig.14))
If the supply voltage drops too low to guarantee the
integrity of the data in the I
2
C-bus latches, the power-on
reset cycle will start. All latches will be set to a pre-defined
state, pin DIAG will be pulled LOW to indicate that a
power-on reset has occurred, and bit D7 of data byte 2 is
also set for the same reason. When D0 of instruction
byte 1 is set, the power-on flag resets, pin DIAG is
released and the amplifier will then enter its start-up cycle.
Diagnostic output
Pin DIAG indicates clipping, thermal protection
pre-warning of amplifier and voltage regulator sections,
short-circuit protection, low and high battery voltage.
Pin DIAGisan open-drainoutput, is activeLOW, and must
be connected to an external voltage via an external pull-up
resistor. If a failure occurs, pin DIAG remains LOW during
the failure and no clipping information is available. The
microcontroller can read the failure information via the
I
2
C-bus.
AMPLIFIERS
Muting
Ahard mute and a soft mute can both be performed via the
I
2
C-bus. A hard mute mutes the amplifier within 0.5 ms.
A soft mute mutes the amplifier within 20 ms and is less
audible. A hard mute is also activated if a voltage of 8 V is
applied to pin STB.
Temperature protection
If the average junction temperature rises to a temperature
value that has been set via the I
2
C-bus, a thermal
protectionpre-warningisactivatedmakingpin DIAGLOW.
If the temperature continues to rise, all four channels will
be muted to reduce the output power (soft thermal
clipping). The value at which the temperature mute control
activates is fixed; only the temperature at which the
thermal protection pre-warning signal occurs can be
specified by bit D4 in instruction byte 3. If implementing
the temperature mute control does not reduce the average
junction temperature, all the power stages will be switched
off (muted) at the absolute maximum temperature T
j(max)
.
Offset detection
Offset detection can only be performed when there is no
input signal to the amplifiers, for instance when the
external digital signal processor is muted after a start-up.
The output voltage of each channel is measured and
相關PDF資料
PDF描述
TDA8742H Satellite sound circuit with noise reduction
TDA8922B 2 X 50 W class-D power amplifier
TDA9102CT H/V PROCESSOR FOR TTL V.D.U
TDA9102T H/V PROCESSOR FOR TTL V.D.U
TDA9102F H/V PROCESSOR FOR TTL V.D.U
相關代理商/技術參數
參數描述
TDA8589J/N1,112 功能描述:音頻放大器 MULTI CHIP MODULE IPAS2.45 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
TDA8591 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:4 X 44 W into 4 or 4 X 75 W into 2 quad BTL car radio power amplifier
TDA8591J 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:4 X 44 W into 4 or 4 X 75 W into 2 quad BTL car radio power amplifier
TDA8591J/N1,112 功能描述:音頻放大器 4 X 44 W INTO 4 OHM OR 4 X 75 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
TDA8594 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:I2C-bus controlled 4 X 50 W power amplifier
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*