- 您現在的位置：買賣IC網 > PDF目錄372453 > TDA7575 (意法半導體) MULTIFUNCTION DUAL BRIDGE POWER AMPLIFIER WITH INTEGRATED DIGITAL DIAGNOSTICS PDF資料下載
參數資料
| 型號： | TDA7575 |
| 廠商： | 意法半導體 |
| 元件分類： | 音頻放大器 |
| 英文描述： | MULTIFUNCTION DUAL BRIDGE POWER AMPLIFIER WITH INTEGRATED DIGITAL DIAGNOSTICS |
| 中文描述： | 多功能雙橋功率放大器，集成了數字診斷 |
| 文件頁數： | 8/17頁 |
| 文件大?。?/td> | 193K |
| 代理商： | TDA7575 |
TDA7575
8/17
It is recommended to minimize the impedance on the board between OUT2 and the load in order to minimize
THD distortion. It is also recommended to control the maximum mismatch impedance between VCC pins
(PIN21/PIN22 respect to PIN33/PIN34) and between PWGND pins (PIN24/PIN25 respect to PIN30/PIN31),
mismatch that must not exceed a value of 20 mOhm.
With 1OHM feature settled the active input is IN2 (PIN17 and PIN18), therefore IN1 pins should be let floating.
It is possible to set the load capability acting on 1OHM pin as follows:
1OHM PIN (PIN15) < 1.5V: two channels mode (for a minimum load of 2 OHM)
1OHM PIN (PIN15) > 2.5V: one channel mode (for 1 OHM load).
IT IS TO REMEMBER THAT 1 0HM FUNCTION IS A HARDWARE SELECTION.
Therefore it is recommended to leave 1OHM PIN floating or shorted to GND to set the two channels mode con-
figuration, or to short 1OHM PIN to VCC to set the one channel (1OHM) configuration.
I2C Abilitation Setting
It is possible to disable the I
2
C interface by acting on I
2
C PIN (PIN16) and control the TDA7575 by means of the
usual ST-BY and MUTE pins. In order to activate or deactivate this feature, I
2
C PIN must be set as follows:
I2C PIN (PIN16) < 1.5V: I
2
C bus interface deactivated
I2C PIN (PIN16) > 2.5V: I
2
C bus interface activated
It is also possible to let I
2
C PIN floating to deactivate the I
2
C bus interface, or to short I
2
C PIN to VCC to activate
it.
In particular:
I
2
C ENABLED: I
2
C pin (PIN16) > 2.5V
– STD MODE: Vstby (PIN5) > 3.5V, IB2(D1)=0
– HE MODE: Vstby (PIN5) > 3.5V, IB2(D1)=1
– PLAY MODE: Vmute (pin 4) >3.5V, IB1 (D2) = 1
The amplifier can always be switched off by putting Vstby to 0V, but with I
2
C enabled it can be turn on only
through I
2
C (with Vstby>3.5V).
I
2
C DISABLED: I
2
C pin (PIN16) < 1.5V
– STD MODE: 3.5V < stby (PIN5) < 5
– HE MODE: Vstby (PIN5) > 7V
– PLAY MODE: Vmute (pin 4) >3.5V
For both STD and HE MODE the play/mute mode can be set acting on Vmute pin.
相關PDF資料 |
PDF描述 |
|---|---|
| TDA8175 | TV VERTICAL DEFLECTION OUTPUT CIRCUIT |
| TDA8176 | TV VERTICAL DEFLECTION SYSTEM FOR TV AND MONITORS |
| TDA8177F | VERTICAL DEFLECTION BOOSTER |
| TDA8177 | VERTICAL DEFLECTION BOOSTER |
| TDA8178 | TV VERTICAL DEFLECTION BOOSTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TDA7575B | 功能描述:音頻放大器 2 x 75W Multifunct Dual-Bridge Pwr Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TDA7575BPD | 功能描述:音頻放大器 2 x 75W Multifunct Dual-Bridge Pwr Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TDA7575BPDTR | 功能描述:音頻放大器 2 x 75W Multifunct Dual-Bridge Pwr Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TDA7575PD | 功能描述:音頻放大器 INFOTAINMENT S PWR RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TDA7575PDTR | 功能描述:音頻放大器 INFOTAINMENT S PWR RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。