- 您現在的位置：買賣IC網 > PDF目錄373624 > TDA7550 (意法半導體) DIGITAL SIGNAL PROCESSING IC FOR SPEECH AND AUDIO APPLICATIONS PDF資料下載
參數資料
| 型號： | TDA7550 |
| 廠商： | 意法半導體 |
| 元件分類： | 數字信號處理 |
| 英文描述： | DIGITAL SIGNAL PROCESSING IC FOR SPEECH AND AUDIO APPLICATIONS |
| 中文描述： | 數字信號和音頻應用語音處理IC |
| 文件頁數： | 6/12頁 |
| 文件大?。?/td> | 118K |
| 代理商： | TDA7550 |
24 BIT DSP CORE
The DSP Core is a general purpose 24-bit DSP.
The main feature of the DSP Core are listed be-
low:
50Mhz Operating Frequency (50 MIPS)
Single cycle multiply and accumulate
2x56-bit Accumulators
Double precision multiply
Convergent rounding
Scaling and saturation arithmetic
48-bit or 2x24-bit parallel moves
64 interrupt vector locations
Fast or long interrupts possible
Programmable interrupt priorities and masking
8 each Address Registers, Address Offset
Registers and Address Modulo Registers
Linear, Reverse Carry, Multiple Buffer Modulo,
Multiple Wrap-around Modulo address arith-
metic
Post-increment or decrement by 1 or by offset,
Index by offset, predecrement address
Repeat instruction and zero overhead DO
loops
Hardware stackcapable of nesting 7 DO loops
or 15 interrupts/subroutines
Bit manipulation instructions possible on all
registers and memory locations. Also Jump on
bit test.
Data Arithmetic Logic Unit (DALU)
Address Generation Unit (AGU)
Program Control Unit (PCU)
Three Data Buses
Three Address Buses
Internal Data Bus Switch
bit Manipulation Unit
Debug Logic
Memories
16384x24-bit Program ROM used for storing the
program code.
16384x24-bit Data RAM used for storing Data.
DSP peripherals
Serial Audio Interface (SAI)
The SAI is used to deliver digital audio to the
DSP from an external source and to deliver
digital audio from the DSP to an external DAC.
It allows using an external CODEC. The main
features of this block are listed below:
– One Data Transmission Line
– One Data Reception Line
– Master and Slave Operating Modes
– Reference clock for transmission supplied
– Transmit and Receive Interrupt Logic
modified to trigger on Left/Right data pairs
– Receive and Transmit Data Registers have
two locations to hold left and right data
I
2
C interface/SPI
The inter integrated-circuit bus is a simple bi-
directional two-wire bus used for efficient inter
IC control. All I
2
C bus compatible devices in-
corporate an on-chip interface which allows
them communicate directly with each via the
I
2
C bus.
Every component hoocked up to the I
2
C bus
has it’s own unique address whether it is a
CPU, memory or some other complex function
chip. Each of these chips can act as a receiver
and/or transmitter depending on it’s functional-
ity.
The Serial Peripheral Interface (SPI) can be
enabled instead of the I
2
C interface. During an
SPI transfer, data is trasmitted and received
simulaneously. A serial clock line synchronizes
shifting and sampling of the information on the
two serial data lines. A slave select line allows
individual selection of a slve SPI device. When
an SPI transfer occurs an 8-bit word is shifted
out one data pin while another 8-bit character
is simultaneously shifted in a second data pin.
The central element in the SPI system is the
shift register and the read data buffer. The sys-
tem is single buffered in the trasmit direction
and double buffered in the receive direction.
EMI
The External Memory Interface is viewed as a
memory mapped peripheral. Data transfers are
performed by moving data into/from data regis-
ters and the control is exercised by polling
status flags in the control/status register or by
servicing interrupts. An external memory write
is executed by writing data into the Data Write
register. An external memory read operation is
executed by either writing to the Offset register
or reading the Data read register, depending
on the configuration.
The main features of the EMI are listed below:
– Data bus width fixed at 4 bits for DRAM and
8 bits for SRAM
– 22 bit address bus multiplexed with an 8 bit
data bus
– Three choices of data word lenghths, 8, 16 or
24 bits in SRAM mode
– Two choices of data word lenght, 16 or 24
bits in DRAM mode
– Thirteen address lines 2
26
= 256Mbits
TDA7550R - TDA7550 - TDA7551 - TDA7552 - TDA7553
6/12
相關PDF資料 |
PDF描述 |
|---|---|
| TDA7550R | DIGITAL SIGNAL PROCESSING IC FOR SPEECH AND AUDIO APPLICATIONS |
| TDA7551 | DIGITAL SIGNAL PROCESSING IC FOR SPEECH AND AUDIO APPLICATIONS |
| TDA7552 | DIGITAL SIGNAL PROCESSING IC FOR SPEECH AND AUDIO APPLICATIONS |
| TDA7553 | DIGITAL SIGNAL PROCESSING IC FOR SPEECH AND AUDIO APPLICATIONS |
| TDA7560 | 4 x 45W QUAD BRIDGE CAR RADIO AMPLIFIER PLUS HSD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TDA7550R | 制造商:STMicroelectronics 功能描述: |
| TDA7551 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:DIGITAL SIGNAL PROCESSING IC FOR SPEECH AND AUDIO APPLICATIONS |
| TDA7552 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:DIGITAL SIGNAL PROCESSING IC FOR SPEECH AND AUDIO APPLICATIONS |
| TDA7553 | 功能描述:數字信號處理器和控制器 - DSP, DSC RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT |
| TDA7555 | 功能描述:音頻 DSP RoHS:否 制造商:Texas Instruments 工作電源電壓: 電源電流: 工作溫度范圍: 安裝風格: 封裝 / 箱體: 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。