參數資料
型號： TDA5149
廠商： NXP Semiconductors N.V.
英文描述： 12 V Voice Coil Motor VCM driver and spindle motor pre-driver combination chip
中文描述： 12伏氯乙烯音圈電機驅動器和主軸電機預驅動芯片組合
文件頁數： 8/28頁
文件大?。?/td> 148K
代理商： TDA5149
1996 May 06
8
Philips Semiconductors
Product specification
12 V Voice Coil Motor (VCM) driver and
spindle motor pre-driver combination chip
TDA5149G
FUNCTIONAL DESCRIPTION
Spindle
The spindle section contains both the low and high side
pre-drivers for a three phase DC brushless motor.
The digital commutation control, using the timing
information provided via the serial port, is responsible for
the proper switch-on and switch-off of the external power
FETs. It is also responsible for selecting the correct BEMF
comparator.
For optimum power efficiency, a continuous PWM method
is used to control the average current from the power
supply to the motor coils. This PWM mode, by controlling
the average power supply current, produces a lower
torque ripple and thus lower audible noise. In order to
reduce further acoustic noise the TDA5149G is provided
with a soft switching circuit to turn-on and turn-off linearly
the switching current under PWM control. The switching
transition time is controlled by the digital commutation
circuit and is fixed to 50% of the time between two
zero-crossings, i.e. 30
°
of the electrical revolution.
Soft switching is achieved by activating, during
commutation, a free-running duty-cycle modulator
controlled by a linearly decreasing voltage across a
capacitor. This will reduce the current smoothly in the
off-going leg to zero. In conjunction with this additional
PWM open loop, the average current control regulates the
sum of the current in the off-going and on-going leg.
This method requires two PWM control loops; one to
control the average current (main loop) and one to control
the current in the off-going leg. The swapping of the two
loops is realized with a pair of analog switches that are
sequentially switched by the digital commutation circuitry.
The PWM control also causes PWM pulses on the back
EMF. These pulses disturb correct sensing of the back
EMF for the zero-crossing detection. Consequently,
edge-triggered latches are inserted behind the back EMF
comparators, thus ensuring reliable back EMF sensing.
In the SPINMODE, programmable via the serial bus, the
user can feed their own commutation pulses to the
pre-drivers and control the motor in the stepper-motor
mode. The commutation pulses are applied to the
TDA5149G via the serial bus by setting the COMMCLK bit
successively to logic 1 and logic 0.
The different control modes of the TDA5149G can be
commanded via the serial bus. These modes are as
follows:
Sleep mode: all analog circuits, except the power supply
monitor, are switched off to reduce the power
consumption of both the 12 and 5 V supplies.
Disable mode: the output voltage of all pre-drivers is
LOW thus the external power MOSFETs are not
conducting.
Brake mode: all low side pre-drivers are turned on
(output voltage HIGH) thus switching on the low-side
power MOSFETs. In this way the back EMF voltage of
the motor is short-circuited to ground.
Voice coil motor
The VCM is a linear, symmetrical, class AB, H-bridge type
power amplifier with all power devices on-chip. The driver
is a transconductance amplifier that controls the output
currents up to 1.65 A. The driver is constructed in a
master-slave configuration with the zero current level
internally adjusted in such a way that it corresponds to the
middle of the output swing. Moreover, the gain of the slave
has been made greater than 1 in order to ensure full
saturation of the driver output VCM+.
The gain of the closed loop is programmable, using the
V
GAINSEL
bit. This bit can be programmed via the serial
bus. A sense resistor (R
s
) allows the measurement of the
VCM current. The voltage across this resistor is connected
to an accurate sense amplifier with a typical gain of 5.
The output of the sense amplifier (V
CMSENSOUT
) is fed back
to the input of the VCM amplifier. Because of the symmetry
of the circuit, the compensation network can be connected
between the VCM1 input and the VCM
output.
Control modes such as VCM-BRAKE, VCM-DISABLE and
VCM-PARK can be controlled via the serial bus.
Latch drivers
The TDA5149G provides the possibility of driving an
external latch to secure the VCM heads. There are two
modes; the activate mode (LACTIVE) and the hold mode
(LHOLD). The hold mode is used to preserve power.
Both modes are controlled via the serial bus. The drivers
are switched off during the SLEEP mode or in the event of
a power-down.
相關PDF資料
PDF描述
TDA5149G 12 V Voice Coil Motor VCM driver and spindle motor pre-driver combination chip
TDA5155 Pre-amplifier for Hard Disk Drive HDD with MR-read/inductive write heads
TDA5155X Pre-amplifier for Hard Disk Drive HDD with MR-read/inductive write heads
TDA5240 Brushless DC motor drive circuit
TDA5240T Brushless DC motor drive circuit
相關代理商/技術參數
參數描述
TDA5149G 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:12 V Voice Coil Motor VCM driver and spindle motor pre-driver combination chip
TDA5150 功能描述:射頻發射器 WIRELESS CONTROLLER RoHS:否 制造商:Micrel 類型:ASK Transmitter 封裝 / 箱體:SOT-23-6 工作頻率:300 MHz to 450 MHz 封裝:Reel
TDA5150HTMA1 制造商:Infineon Technologies AG 功能描述:Multiband Transmitter 10-Pin TSSOP T/R 制造商:Infineon Technologies AG 功能描述:CONTROL - Tape and Reel 制造商:Infineon Technologies AG 功能描述:IC TX MULTI-CH/BAND 10-TSSOP
TDA5153 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Pre-amplifier for Hard Disk Drive HDD with MR-read/inductive write heads
TDA5153AG 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Pre-amplifier for Hard Disk Drive HDD with MR-read/inductive write heads
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*