- 您現在的位置：買賣IC網 > PDF目錄385914 > TCS59SM804BFTL-70 (Toshiba Corporation) 16M×4Banks×4Bits Synchronous DRAM(4組16M×4位同步動態RAM) PDF資料下載
參數資料
| 型號： | TCS59SM804BFTL-70 |
| 廠商： | Toshiba Corporation |
| 英文描述： | 16M×4Banks×4Bits Synchronous DRAM(4組16M×4位同步動態RAM) |
| 中文描述： | 1,600 × 4Banks × 4Bits同步DRAM（4組1,600 × 4位同步動態RAM）的 |
| 文件頁數： | 33/49頁 |
| 文件大?。?/td> | 2423K |
| 代理商： | TCS59SM804BFTL-70 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁當前第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁
TC59SM816/08/04BFT/BFTL-70,-75,-80
2000-03-14 33/49
1-7
Read with Auto Precharge command
(RAS
=
H, CAS
=
L, WE
=
H, BS0, BS1
=
Bank, A10
=
H, A0~A9, A11
=
Column Address)
The Read with Auto Precharge command automatically performs the Precharge operation after the
Read operation. When the CAS Latency
=
3, the internal precharge starts two cycles before the last
data is output. When the CAS Latency
=
2, the internal precharge starts one cycle before the last data
is output (Figure 15). This command must not be interrupted by any other command.
The A11 input is “Don’t care” on the TC59SM808BFT/BFTL and the A9 and A11 inputs are “Don’t care”
on the TC59SM816BFT/BFTL.
1-8
Mode Register Set command
(RAS
=
L, CAS
=
L, WE
=
L, BS0, BS1, A0~A12
=
Register Data)
The Mode Register Set command programs the values of CAS latency, Addressing Mode and Burst
Length in the Mode Register. The default values in the Mode Register after power-up are undefined,
therefore this command must be issued during the power-up sequence. Also, this command can be issued
while all banks are in the idle state.
1-9
No-Operation command
(RAS
=
H, CAS
=
H, WE
=
H)
The No-Operation command simply performs no operation.
1-10 Burst stop command
(RAS
=
H, CAS
=
H, WE
=
L)
The Burst stop command is used to stop the burst operation. This command is valid during a Full Page
Burst operation. During other types of Burst operation, the command is illegal.
1-11 Device Deselect command
(CS
=
H)
The Device Deselect command disables the command decoder so that the RAS , CAS , WE and
Address inputs are ignored. This command is similar to the No-Operation command.
1-12 Auto Refresh command
(RAS
=
L, CAS
=
L, WE
=
H, CKE
=
H, BS0, BS1, A0~A12
=
Don’t care)
The Auto Refresh command is used to refresh the row address provided by the internal refresh counter.
The Refresh operation must be performed 8192 times within 64 ms. The next command can be issued
after t
RC
from the end of the Auto Refresh command. When the Auto Refresh command is issued, All
banks must be in the idle state. The Auto Refresh operation is equivalent to the CAS -before-RAS
operation in a conventional DRAM.
相關PDF資料 |
PDF描述 |
|---|---|
| TCS59SM804BFTL-75 | 16M×4Banks×4Bits Synchronous DRAM(4組16M×4位同步動態RAM) |
| TCS59SM804BFTL-80 | 16M×4Banks×4Bits Synchronous DRAM(4組16M×4位同步動態RAM) |
| TCS59SM808BFT-75 | 8M×4Banks×8Bits Synchronous DRAM(4組8M×8位同步動態RAM) |
| TCS59SM808BFT-80 | 8M×4Banks×8Bits Synchronous DRAM(4組8M×8位同步動態RAM) |
| TCS59SM808BFTL-70 | 8M×4Banks×8Bits Synchronous DRAM(4組8M×8位同步動態RAM) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TCS5BB6A0 | 制造商:Digital Persona 功能描述:SPI USB - TRAY STAINLESS STEEL BEZEL - Trays 制造商:UPEK 功能描述:SPI USB - TRAY STAINLESS STEEL BEZEL - Trays |
| TCS5BB6A2 | 制造商:Digital Persona 功能描述:TCS5B (USB CHIPSET) REEL STAINLESS STEEL BEZEL SMALL PACKAGE - Bulk 制造商:UPEK 功能描述:TCS5B (USB CHIPSET) REEL STAINLESS STEEL BEZEL SMALL PACKAGE - Bulk |
| TCS5BE6B1 | 制造商:Digital Persona 功能描述:TCS5BE6B1 - Bulk 制造商:UPEK 功能描述:TCS5BE6B1 - Bulk |
| TCS5BF6A1 | 制造商:Digital Persona 功能描述:TCS5B (USB CHIPSET) TRAY STAINLESS STEEL BEZEL LARGE PACKAGE - Bulk 制造商:UPEK 功能描述:TCS5B (USB CHIPSET) TRAY STAINLESS STEEL BEZEL LARGE PACKAGE - Bulk |
| TCS5BF6A2 | 制造商:Digital Persona 功能描述:TCS5B (USB CHIPSET) REEL STAINLESS STEEL BEZEL LARGE PACKAGE - Bulk 制造商:UPEK 功能描述:TCS5B (USB CHIPSET) REEL STAINLESS STEEL BEZEL LARGE PACKAGE - Bulk |
發布緊急采購，3分鐘左右您將得到回復。