參數資料
型號： TC9444F
廠商： Toshiba Corporation
英文描述： Single-Chip karaoke IC II
中文描述： 單芯片集成電路二卡拉OK
文件頁數： 11/29頁
文件大?。?/td> 315K
代理商： TC9444F
TC9444F
2002-01-11
11
3.2
BOOT Command
One-byte command to initialize coefficient RAM.
Initializes coefficient RAM values to the internal BOOT ROM values, retaining the other command
interface settings.
After the BOOT command is received, initialization completes in a
1
-fs cycle. Boot release is not
required.
When reset is made by setting the
RESET
pin to “L”, boot is still executed.
3.3
MUTE Command
One-byte command to clear data RAM and delay RAM, and to execute a soft mute using the digital
attenuator.
Table 3.2 MUTE Command
CL
CH
3
2
1
0
1
0
0
RAMCLR
MUTE
Note 5: At a reset, the initial value is CL 0H.
MUTE: MUTE “H” sets soft mute.
RAMCLR: RAMCLR “H” clears data RAM and delay RAM.
At a soft mute, the time constant is determined by the operation sampling frequency and the time
constant selection bit set by the ATTA command. After the soft mute is released, the digital
attenuator is restored to the set level.
In data RAM, sequentially writing all-zero data (fixing the input data to 000000H) while RAMCLR
“H” clears data RAM. Therefore, the number of fs cycles required to completely clear data RAM
depends on the program. Normally, several cycles are required.
For a program which is written to in one place only, a
1
28-word update takes no more than 3 ms.
In delay RAM, after RAMCLR H, 0000H is sequentially written to delay RAM at subsequent
write operations (INIT operation).
When using delay RAM to significantly change the effect of the SFC processing, to clear the data in
RAM, take the following steps. First set the MUTE bit. Then, after waiting only the length of the
digital attenuator time constant, set RAMCLR to “H” to clear the data in RAM. Then set the
RAMCLR and MUTE bits to “L”. This will enable you to change the signal processing content without
any switching noise.
3.4
KEYCON Command
One-byte command to control the amount of key shift. The CL value indicates the amount of key
shift.
The difference between the 20H command and the 28H command is the point at which key control
processing completely stops. Using the 20H command to turn key control off disables the use of
internal delay RAM in the key control processing, thus allowing delay RAM to be allocated to other
processing.
The amount of key shift set by the KEYCON command applies to both L and R stereo key control
and to monaural key control. The key shift is set in semitone steps.
As delay RAM is used in key control processing, when switching the key shift setting between 0 and
a value other than 0, the signal is intermittent. The soft mute automatically comes on to avoid
switching noise at this time. After the command is issued, the following steps are performed
automatically.
Mute
Internal settings switched
Mute released
This series of processing operations takes around 46 ms to execute.
相關PDF資料
PDF描述
TC9462F DIGITAL SERVO SINGLE CHIP PROCESSOR BUILT IN 1BIT DA CONVERTER
TC9464FN TOSHIBA CMOS DIGITAL INTEGRATED CIRCUIT SILICON MONOLITHIC
TC9465F SINGLE CHIP KARAOKE LSI
TC9470FN ?-? Modulation DA Converter with Built-in 8-Times Oversampling Digital Filter/Dynamic Digital Bass Boost/Analog Filter
TC94A04AF 1 CHIP AUDIO DIGITAL PROCESSOR
相關代理商/技術參數
參數描述
TC9446F 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:Audio Digital Processor for Decode of Dolby Digital (AC-3), MPEG2 Audio
TC9446F-033 制造商:Panasonic Industrial Company 功能描述:IC
TC9446FG 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:Audio Digital Processor for Decode of Dolby Digital (AC-3), MPEG2 Audio
TC9447F 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:Single-Chip Audio Digital Signal Processor
TC9452F 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:SINGLE CHIP SURROUND LSI
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*