參數資料
型號： TC9205M-DS-R03
廠商： Electronic Theatre Controls, Inc.
元件分類： 圓形連接器
英文描述： Circular Connector; MIL SPEC:MIL-C-26482, Series I, Crimp; Body Material:Aluminum; Series:PT06; No. of Contacts:3; Connector Shell Size:8; Connecting Termination:Crimp; Circular Shell Style:Straight Plug; Body Style:Straight
中文描述： 5端口10/100/1000智能以太網交換機
文件頁數： 16/51頁
文件大小： 1661K
代理商： TC9205M-DS-R03
TC9205M
Preliminary Data Sheet
2.2
Transmit MAC
The Transmit MAC section assembles the MAC frames stored in the transmit FIFO and controls their
transmission onto the media via external PHY entities. It appends the standard preamble and start of
frame delimiter to the transmitted packets. The MAC also controls the interframe gap time during
transmission, maintaining for default the standard minimum interframe gap of 96-bit time. This value can
be changed in the EEPROM register setting.
For Half Duplex mode the Transmit MAC meets CSMA/CD
IEEE 802.3
requirements. The FIFO logic
manages frame retransmission for early collision conditions or discards the frame if late collision occurs.
It also follows the truncated binary exponential backoff algorithm, collision and jamming procedures.
The transmit FIFO stores the packets which are ready for transmission in the main memory queues. If
there is no packet ready in the transmit FIFO before the current packet completes its transmission, an
underrun condition has occurred and the mechanism will generate a signal to indicate FIFO underrun
event, but if the switch core transfers the rest of the packet(s) into the FIFO, the Transmit MAC will safely
discard it without affecting the next packet. Underrun conditions never occur if the system is operating at
the recommended clock frequency or higher.
For full duplex mode TC9205M implements the flow control algorithm according to the
IEEE 802.3x
standard,
using the XON/XOFF method. Full duplex flow control can be configured automatically, by auto-negotiation
result, or manually, pin configuration and/or EEPROM settings, to enable/disable the function.
The TC9205M executes backpressure algorithm for half duplex flow control supporting both collision
based and carrier based backpressure. Both modes are based on carrier sense forced collisions and an
aggressive backoff algorithm. The forced consecutive collisions generated for flow control purposes can
be limited to a maximum of 28 collisions if this option is selected. This feature helps to avoid HUB
partitioning in heavy traffic. The number of collisions can be adjusted in EEPROM settings.
MAC Block Diagram
Rx FIFO
Rx MAC
Tx MAC
Flow
Control
Tx FIFO
Fifo Control Logic
System Interface
MAC
RMII
PHY Layer
RMII Rx Data (2)
Tx Data (64)
FC Insert
Tme Value (16)
Rx Data (64)
RMII Tx Data (2)
Confidential.
Copyright
2003, IC Plus Corp.
16/51
July 30, 2003
TC9205M-DS-R03
相關PDF資料
PDF描述
TCC0204-125 RF & Microwave Transistors VHF/UHF Applications(用于超高頻和甚高頻的RF和微波晶體管)
TCL100DC1-A 6 and 12 Volt, 75 to 450 Watts Wet Cell Lead Calcium Battery
TCL100DA1-A 6 and 12 Volt, 75 to 450 Watts Wet Cell Lead Calcium Battery
TCL100DA1-ACF1 6 and 12 Volt, 75 to 450 Watts Wet Cell Lead Calcium Battery
TCL100DA1-ACF2 6 and 12 Volt, 75 to 450 Watts Wet Cell Lead Calcium Battery
相關代理商/技術參數
參數描述
TC9208 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:HIGH TENSION SUSTAINING ANALOG FUNCTION SWITCH
TC9208M 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Port 10/100/1000 Smart Ethernet Switch
TC9208M-DS-R05 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Port 10/100/1000 Smart Ethernet Switch
TC9208M-DS-R06 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Port 10/100/1000 Smart Ethernet Switch
TC9208N 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:HIGH TENSION SUSTAINING ANALOG FUNCTION SWITCH
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*