參數資料
型號： TC850ILW
廠商： Microchip Technology
文件頁數： 9/26頁
文件大?。?/td> 0K
描述： IC ADC 15BIT FAST 44PLCC
標準包裝： 27
位數： 15
采樣率（每秒）： 40
數據接口： 并聯
轉換器數目： 1
電壓電源： 雙 ±
工作溫度： -25°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 44-LCC（J 形引線）
供應商設備封裝： 44-PLCC
包裝： 管件
輸入數目和類型： 1 個差分，單極
2006 Microchip Technology Inc.
DS21479C-page 17
TC850
Figure 8-3 shows a typical interface to a
μP I/O port or
single-chip
μC. The TC850 operates in the Continuous
mode and can either interrupt the
μC/μP or be polled
with an input pin.
FIGURE 8-3:
Interface to Typical
μP I/O
Port or Single Chip
μC
Since the PA0-PA7 inputs are dedicated to reading A/D
data, the A/D CS/CE inputs can be enabled continu-
ously. In Continuous mode, data must be read in 3
bytes, as shown in Table 6-1. The required RD pulses
are provided by a
μC/μP output pin.
The circuit of Figure 8-3 can also operate in the
Demand mode, with the start-up conversion strobe
generated by a
μC/μP output pin. In this case, the L/H
and CONT/DEMAND inputs can be controlled by I/O
pins and the RD input connected to digital ground.
8.3
Demand Mode Interface Timing
When CONT/DEMAND input is LOW, the TC850
performs a conversion each time CE and CS are active
and WR is strobed LOW.
The Demand mode conversion timing is shown in
Figure 8-1. BUSY goes LOW and data is valid 1155
clock pulses after WR goes LOW. After BUSY goes
low, 125 additional clock cycles are required before the
next conversion cycle will begin.
Once conversion is started, WR is ignored for 1100
internal clock cycles. After 1100 clock cycles, another
WR pulse is recognized and initiates a new conversion
when the present conversion is complete. A negative
edge on WR is required to begin conversion. If WR is
held LOW, conversions will not occur continuously.
The A/D conversion data is valid on the falling edge of
BUSY and remains valid until one-half internal clock
cycle before BUSY goes HIGH on the succeeding
conversion. BUSY can be monitored with an I/O pin to
determine end of conversion or to generate a
μP
interrupt.
In Demand mode, the three data bytes can be read in
any desired order. The TC850 is simply regarded as
three bytes of memory and accessed accordingly. The
bus output timing is shown in Figure 8-2.
8.4
Continuous Mode Interface Timing
When the CONT/DEMAND input is HIGH, the TC850
performs conversions continuously. Data will be valid
on the falling edge of BUSY and all three bytes must be
read within 443-1/2 internal clock cycles of BUSY going
LOW. The timing diagram is shown in Figure 8-3.
In Continuous mode, OVR/POL and L/H byte-select
inputs are ignored. The TC850 automatically cycles
through three data bytes, as shown in Table 6-1. Bus
output timing in the Continuous mode is shown in
DB0
DB1
DB2
DB3
DB4
DB5
DB6
DB7
BUSY
RD
PB0
CS
NC
CE
WR
+5V
PA0
PA1
PA2
PA3
PA4
PA5
PA6
PA7
INTERRUPT
CONT/DEMAND
mC OR mP
I/O PORT
TC850
相關PDF資料
PDF描述
MS27467T17F55SLC CONN HSG PLUG 55POS STRGHT SCKT
MS27472T18B11P CONN RCPT 11POS WALL MT W/PINS
VE-B40-IV-F4 CONVERTER MOD DC/DC 5V 150W
D38999/20WD5PNLC CONN HSG RCPT 5POS WALL MT PINS
LM4819LD/NOPB IC AMP AUDIO PWR .35W MONO 8LLP
相關代理商/技術參數
參數描述
TC850ILW713 功能描述:模數轉換器 - ADC 16 Bit Hi Speed A/D RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
TC8521AM 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:REAL TIME CLOCK ケ
TC8521AP 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:REAL TIME CLOCK ケ
TC8566AF 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:FLOPPY DISK CONTROLLER
TC8569AF 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:FLOPPY DISK CONTROLLER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*