參數資料
型號： TC7109CKW713
廠商： Microchip Technology
文件頁數： 30/30頁
文件大?。?/td> 0K
描述： IC ADC 12BIT HANDSHAKE 44-MQFP
標準包裝： 900
位數： 12
數據接口： 串行，并聯
轉換器數目： 1
電壓電源： 雙 ±
工作溫度： 0°C ~ 70°C
安裝類型： 表面貼裝
封裝/外殼： 44-QFP
供應商設備封裝： 44-MQFP（10x10）
包裝： 帶卷 (TR)
輸入數目和類型： 1 個差分，單極
2006 Microchip Technology Inc.
DS21456C-page 9
TC7109/A
3.1.6
DIFFERENTIAL REFERENCE
The reference voltage can be generated anywhere
within the power supply voltage of the converter. Roll-
over voltage is the main source of Common mode
error, caused by the reference capacitor losing or gain-
ing charge, due to stray capacity on its nodes. With a
large Common mode voltage, the reference capacitor
can gain charge (increase voltage) when called upon to
de-integrate a positive signal and lose charge
(decrease voltage) when called upon to de-integrate a
negative input signal. This difference in reference for
(+) or (–) input voltages will cause a rollover error. This
error can be held to less than 0.5 count, worst-case, by
using a large reference capacitor in comparison to the
stray capacitance. To minimize rollover error from
these sources, keep the reference Common mode
voltage near or at analog common.
3.2
Digital Section
The digital section is shown in Figure 3-2 and includes
the clock oscillator and scaling circuit, a 12-bit binary
counter with output latches and TTL compatible three-
state output drivers, UART handshake logic, polarity,
over range, and control logic. Logic levels are referred
to as LOW or HIGH.
Inputs driven from TTL gates should have 3k
Ω to 5kΩ
pull-up resistors added for maximum noise immunity.
For minimum power consumption, all inputs should
swing from GND (LOW) to V+ (HIGH).
3.2.1
STATUS OUTPUT
During a conversion cycle, the Status output goes high
at the beginning of signal integrate and goes low one-
half clock period after new data from the conversion
has been stored in the output latches (see Figure 3-1).
The signal may be used as a “data valid” flag to drive
interrupts, or for monitoring the status of the converter.
(Data will not change while status is low.)
3.2.2
MODE INPUT
The Output mode of the converter is controlled by the
MODE input. The converter is in its “Direct” Output
mode, when the MODE input is LOW or left open. The
output data is directly accessible under the control of
the chip and byte enable inputs (this input is provided
with a pull-down resistor to ensure a LOW level when
the pin is left open). When the MODE input is pulsed
high, the converter enters the UART Handshake mode
and outputs the data in 2 bytes, then returns to “Direct”
mode. When the MODE input is kept HIGH, the
converter will output data in the Handshake mode at
the end of every conversion cycle. With MODE = 0
(direct bus transfer), the send input should be tied to
V+. (See “Handshake Mode”.)
3.2.3
RUN/HOLD INPUT
With the RUN/HOLD input high, or open, the circuit
operates normally as a dual slope ADC, as shown in
Figure 3-1. Conversion cycles operate continuously
with the output latches updated after zero crossing in
the De-integrate mode. An internal pull-up resistor is
provided to ensure a HIGH level with an open input.
The RUN/HOLD input may be used to shorten conver-
sion time. If RUN/HOLD goes LOW any time after zero
crossing in the De-integrate mode, the circuit will jump
to auto-zero and eliminate that portion of time normally
spent in de-integrate.
If RUN/HOLD stays or goes LOW, the conversion will
complete with minimum time in de-integrate. It will stay
in auto-zero for the minimum time and wait in auto-zero
for a HIGH at the RUN/HOLD input. As shown in
Figure 3-3, the Status output will go HIGH, 7 clock peri-
ods after RUN/HOLD is changed to HIGH, and the
converter will begin the integrate phase of the next
conversion.
The RUN/HOLD input allows controlled conversion
interface. The converter may be held at Idle in auto-
zero with RUN/HOLD LOW. The conversion is started
when RUN/HOLD goes HIGH, and the new data is
valid when the Status output goes LOW (or is trans-
ferred to the UART; see “Handshake Mode”). RUN/
HOLD may now go LOW, terminating de-integrate and
ensuring a minimum auto-zero time before stopping to
wait for the next conversion. Conversion time can be
minimized by ensuring RUN/HOLD goes LOW during
de-integrate, after zero crossing, and goes HIGH after
the hold point is reached.
The required activity on the RUN/HOLD input can be
provided by connecting it to the buffered oscillator
output. In this mode, the input value measured
determines the conversion time.
相關PDF資料
PDF描述
MS3100E18-1S CONN RCPT 10POS WALL MNT W/SCKT
VI-JNP-MX CONVERTER MOD DC/DC 13.8V 75W
MS27472T12F8SA CONN RCPT 8POS WALL MT W/SCKT
MS27508E12B3SC CONN RCPT 3POS BOX MNT W/SCKT
VI-JNN-MX CONVERTER MOD DC/DC 18.5V 75W
相關代理商/技術參數
參數描述
TC7109CLW 功能描述:模數轉換器 - ADC 13 Bit Fast Recovery RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
TC7109CLW713 功能描述:模數轉換器 - ADC 13 Bit Fast Recovery RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
TC7109CPL 功能描述:模數轉換器 - ADC 13 Bit Fast Recovery RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
TC7109CPL 制造商:Microchip Technology Inc 功能描述:IC 12BIT ADC 7109 DIP40
TC7109CPL 制造商:Microchip Technology Inc 功能描述:Special Function IC Package/Case:40-PDIP
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*