- 您現在的位置：買賣IC網 > PDF目錄361407 > TC70EOA (TelCom Semiconductor, Inc.) MICROMASTER - SYSTEM SUPERVISOR WITH POWER SUPPLY MONITOR, WATCHDOG AND BATTERY BACKUP PDF資料下載
參數資料
| 型號： | TC70EOA |
| 廠商： | TelCom Semiconductor, Inc. |
| 英文描述： | MICROMASTER - SYSTEM SUPERVISOR WITH POWER SUPPLY MONITOR, WATCHDOG AND BATTERY BACKUP |
| 中文描述： | MICROMASTER -系統與電源監視器，看門狗和電池備份督導員 |
| 文件頁數： | 4/7頁 |
| 文件大?。?/td> | 89K |
| 代理商： | TC70EOA |
5-10
TELCOM SEMICONDUCTOR, INC.
strobed within the watchdog timeout period. This action
typically initiates the processor's power-up routine. If the
interruption persists, new reset pulses are generated each
timeout period until RS is strobed. The timeout period is
typically 700msec.
It is often difficult to debug a system while the watchdog
is continuously generating reset pulses. For example, the
watchdog must be disabled when the system is operated
with an in-circuit emulator (ICE). The watchdog disable input
(TC70) is provided for system debugging, (or if the watchdog
timer on-board the processor is to be used). Grounding
WDD disables the watchdog (all other functions remain
intact). For normal watchdog operation, WDD can be tied to
V
DD
.
The software routine that drives the RS strobe must be
in a section of the program that executes frequently enough
so the time between toggles is less than one watchdog
timeout period. The strobe signal can be derived from
microprocessor address, data and/or control signals. Typi-
cal circuit examples are shown in Figure 1.
PIN DESCRIPTION
Pin No
(TC70)
Pin No
(TC71)
Symbol
Description
1
1
V
CCO
V
CC
Output. The higher of V
CC
or V
BATT
is internally switched to this output.
Connect to V
CC
if V
BATT
and V
CCO
are not used.
V
CC
Input. +5V power supply.
GND Input. Ground.
Chip enable input. Chip enable to static RAM or other device to be battery
backed-up. Connect to ground if V
CCO
is not used.
Threshold detector input. When the voltage on threshold detector input (TDI) is
less than 1.3V, threshold detector output (TDO) goes low.
Chip enable output. This line goes low only when CEI is low and V
CC
is above
the RESET threshold.
Threshold detector output. TDO goes low when TDI is less than 1.3V and V
CC
is
greater than V
BATT
. (The threshold detector is turned off when V
CC
is less than
V
BATT
.
Watchdog disable input. Grounding this line disables the watchdog timer (no
RESET pulses are generated after the watchdog timer times out). This input is
provided to facilitate system debug. This input is internally pulled-up and can be
left open, or tied to V
CC
for normal watchdog operation.
Power fail output. This line goes low when V
CC
is below 4.5V nominal. It is used
to write-protect the external device to be battery backed.
RESET/STORE (Bidirectional). An open drain with pull-up (in output mode) that
goes active if:
1. V
CC
falls below 4.5V nominal
2. If pulled low by an external electronic signal or switch closure
3. If the watchdog is not strobed within the minimum watchdog timeout period
4. During power-up and power down
In the input mode, RS is a negative edge triggered input that resets the
watchdog timer when pulled to ground through a 10k
, 5% tolerance resistor.
Backup battery input. Connect to ground if battery backup is not used.
2
3
4
2
3
–
V
CC
GND
CEI
–
4
TDI
5
–
CEO
–
5
TDO
6
–
WDD
–
6
PF
7
7
RS
8
8
V
BATT
DETAILED DESCRIPTION
Precision Power Supply Monitor
The RS pin is immediately driven low any time V
CC
is
below 4.5V nominal. The processor is held in its reset state
during power-up and power-down. RS remains low for a
minimum of 500msec after V
CC
is within tolerance to allow
the power supply and processor to stabilize.
Watchdog Timer
The processor drives the RS pin with an input/output
(I/O) line in series with a voltage divider to V
DD
. Pulling the
bottom of this divider low results in an internal voltage
change (strobe) sufficient to reset the watchdog timer, but
above the V
IL
input threshold of the processor RESET input.
The processor must continuously apply strobes in this
manner within a set period to verify proper software execu-
tion. A momentary reset (500msec minimum) is generated
if a hardware or software failure keeps RS from being
TC70
TC71
MICROMASTER – SYSTEM SUPERVISOR
WITH POWER SUPPLY MONITOR, WATCHDOG
AND BATTERY BACKUP
相關PDF資料 |
PDF描述 |
|---|---|
| TC71EOA | MICROMASTER - SYSTEM SUPERVISOR WITH POWER SUPPLY MONITOR, WATCHDOG AND BATTERY BACKUP |
| TC70CPA | MICROMASTER - SYSTEM SUPERVISOR WITH POWER SUPPLY MONITOR, WATCHDOG AND BATTERY BACKUP |
| TC70EPA | MICROMASTER - SYSTEM SUPERVISOR WITH POWER SUPPLY MONITOR, WATCHDOG AND BATTERY BACKUP |
| TC71 | MICROMASTER - SYSTEM SUPERVISOR WITH POWER SUPPLY MONITOR, WATCHDOG AND BATTERY BACKUP |
| TC7106 | 3-1/2 DIGIT A/D CONVERTERS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TC70EPA | 制造商:TELCOM 制造商全稱:TelCom Semiconductor, Inc 功能描述:MICROMASTER - SYSTEM SUPERVISOR WITH POWER SUPPLY MONITOR, WATCHDOG AND BATTERY BACKUP |
| TC70L3A32K7680 | 功能描述:OSCILLATOR 32.7680 KHZ 3.3V SMD RoHS:是 類別:晶體和振蕩器 >> 振蕩器 系列:TC70 標準包裝:1 系列:VG-4512CA 類型:VCXO 頻率:153.6MHz 功能:三態（輸出啟用） 輸出:LVPECL 電源電壓:3.3V 頻率穩定性:- 工作溫度:-40°C ~ 85°C 電流 - 電源（最大）:60mA 額定值:- 安裝類型:表面貼裝 尺寸/尺寸:0.276" L x 0.197" W（7.00mm x 5.00mm） 高度:0.071"（1.80mm） 封裝/外殼:6-SMD，無引線（DFN，LCC） 包裝:Digi-Reel® 電流 - 電源（禁用）（最大）:- 其它名稱:SER3790DKR |
| TC70L3C32K7680 | 功能描述:OSCILLATOR 32.7680 KHZ 3.3V SMD RoHS:是 類別:晶體和振蕩器 >> 振蕩器 系列:TC70 標準包裝:1 系列:VG-4512CA 類型:VCXO 頻率:153.6MHz 功能:三態（輸出啟用） 輸出:LVPECL 電源電壓:3.3V 頻率穩定性:- 工作溫度:-40°C ~ 85°C 電流 - 電源（最大）:60mA 額定值:- 安裝類型:表面貼裝 尺寸/尺寸:0.276" L x 0.197" W（7.00mm x 5.00mm） 高度:0.071"（1.80mm） 封裝/外殼:6-SMD，無引線（DFN，LCC） 包裝:Digi-Reel® 電流 - 電源（禁用）（最大）:- 其它名稱:SER3790DKR |
| TC70L3I32K7680 | 功能描述:OSCILLATOR 32.7680 KHZ 3.3V SMD RoHS:是 類別:晶體和振蕩器 >> 振蕩器 系列:TC70 標準包裝:1 系列:VG-4512CA 類型:VCXO 頻率:153.6MHz 功能:三態（輸出啟用） 輸出:LVPECL 電源電壓:3.3V 頻率穩定性:- 工作溫度:-40°C ~ 85°C 電流 - 電源（最大）:60mA 額定值:- 安裝類型:表面貼裝 尺寸/尺寸:0.276" L x 0.197" W（7.00mm x 5.00mm） 高度:0.071"（1.80mm） 封裝/外殼:6-SMD，無引線（DFN，LCC） 包裝:Digi-Reel® 電流 - 電源（禁用）（最大）:- 其它名稱:SER3790DKR |
| TC70L5A32K7680 | 功能描述:OSCILLATOR 32.7680 KHZ 3.3V SMD RoHS:是 類別:晶體和振蕩器 >> 振蕩器 系列:TC70 標準包裝:1 系列:VG-4512CA 類型:VCXO 頻率:153.6MHz 功能:三態（輸出啟用） 輸出:LVPECL 電源電壓:3.3V 頻率穩定性:- 工作溫度:-40°C ~ 85°C 電流 - 電源（最大）:60mA 額定值:- 安裝類型:表面貼裝 尺寸/尺寸:0.276" L x 0.197" W（7.00mm x 5.00mm） 高度:0.071"（1.80mm） 封裝/外殼:6-SMD，無引線（DFN，LCC） 包裝:Digi-Reel® 電流 - 電源（禁用）（最大）:- 其它名稱:SER3790DKR |
發布緊急采購，3分鐘左右您將得到回復。