- 您現在的位置：買賣IC網 > PDF目錄361407 > TC70 (TelCom Semiconductor, Inc.) MICROMASTER - SYSTEM SUPERVISOR WITH POWER SUPPLY MONITOR, WATCHDOG AND BATTERY BACKUP PDF資料下載
參數資料
| 型號： | TC70 |
| 廠商： | TelCom Semiconductor, Inc. |
| 英文描述： | MICROMASTER - SYSTEM SUPERVISOR WITH POWER SUPPLY MONITOR, WATCHDOG AND BATTERY BACKUP |
| 中文描述： | MICROMASTER -系統與電源監視器，看門狗和電池備份督導員 |
| 文件頁數： | 5/7頁 |
| 文件大小： | 89K |
| 代理商： | TC70 |
5-11
TELCOM SEMICONDUCTOR, INC.
7
6
5
4
3
1
2
8
Figure 1. TC70 Typical Application
VCC
CE
WDD
VCCO
CEO
TC70
ADDRESS
DECODER
ADDRESS
CMOS
RAM
I/O
RESET
RESET
PROCESSOR
+5V
+3V L
BATTERY
R2
13K
R1
10K
+5V
VBATT
VCC
GND
CEI
RS
data corruption during power up and power down. The
battery switchover circuit compares V
CC
to the V
BATT
input
and connects VCCO to whichever is higher. Switchover
(V
SW
) occurs when V
CC
is 10mV below V
BATT
as V
CC
falls,
and when V
CC
is 10mV more than V
BATT
as V
CC
rises. The
battery switchover comparator has 20mV of hysteresis to
prevent switch chattering if V
CC
falls very slowly.
Integrated Battery Backup (TC71)
The TC71 differs from the TC70 in that it has a Power
Fail (PF) output instead of a gated chip enable (CEI, CEO).
PF must be externally gated with the decode for the CMOS
RAM or other device to be battery-backed. (Many CMOS
RAMs have both CE and CE enables. In this case, the PF
output can be connected directly to the CE input of the RAM).
PF is high as long as V
CC
is greater than 4.5V nominal.
When V
CC
falls below 4.5V nominal, PF is driven low.
Battery switchover for the TC71 is otherwise identical to that
of the TC70.
Supply Monitor Noise Sensitivity
The TC70/71 is optimized for fast response to negative-
going changes in V
DD
. Systems with an inordinate amount
of electrical noise on V
DD
(such as systems using relays),
may require a 0.1
μ
F bypass capacitor to reduce detection
sensitivity. This capacitor should be installed as close to the
TC70/71 as possible to keep the capacitor lead length short.
TYPICAL APPLICATIONS
Figure 1 shows a full feature implementation of the
TC70; Figure 2 shows the TC71. Resistors R1 and R2 of
Figure 2 set the trip point voltage for the early power fail
warning circuit using the TC71 threshold detector.
Resistor Value Selection
The values of R1 and R2 must be chosen to ensure a
valid low strobe level (V
STL
) on RS when the processor I/O
line is low. The use of 10k
,
±
5% tolerance resistors are
recommended. These values result in a nominal strobe level
of 2.83V on RS (min/max of 2.43V/3.24V, assuming
V
DD
= 5.0V
±
10%). Other resistor values can be used, so
long as the additive tolerances of the power supply and
resistor values result in a strobe that falls within V
STH
and
V
STL
under all additive tolerance conditions.
External Override Reset Control
A built-in debounce circuit allows a pushbutton switch
(or other electronic reset signal) to be wire-ORed to RS as
an external reset override (Figure 4). The external reset
signal is required to be an active low signal of at least
20msec in duration. Internally, this input is timed to provide
a minimum reset pulse width output of 500msec.
Threshold Detector
The TC71 issues a low-true output on the TDO pin any
time the TDI pin is less than 1.3V and V
CC
is greater than
V
BATT
. The voltage to be monitored is connected to the TDI
input through a simple resistor divider. The threshold detec-
tor can be used to generate an early power fail warning if the
unregulated DC input to the +5V regulator is available for
monitoring.
Integrated Battery Backup (TC70)
The CEO line (TC70) drives the CE input of a CMOS
RAM or other device to be battery-backed. CEO follows CEI
as long as V
CC
is greater than 4.5V nominal. If V
CC
falls
below 4.5V nominal, CEO is driven to the potential of VCCO
thus write protecting the RAM and preventing accidental
TC70
TC71
MICROMASTER – SYSTEM SUPERVISOR
WITH POWER SUPPLY MONITOR, WATCHDOG
AND BATTERY BACKUP
相關PDF資料 |
PDF描述 |
|---|---|
| TC71COA | MICROMASTER - SYSTEM SUPERVISOR WITH POWER SUPPLY MONITOR, WATCHDOG AND BATTERY BACKUP |
| TC71CPA | MICROMASTER - SYSTEM SUPERVISOR WITH POWER SUPPLY MONITOR, WATCHDOG AND BATTERY BACKUP |
| TC71EPA | MICROMASTER - SYSTEM SUPERVISOR WITH POWER SUPPLY MONITOR, WATCHDOG AND BATTERY BACKUP |
| TC70COA | MICROMASTER - SYSTEM SUPERVISOR WITH POWER SUPPLY MONITOR, WATCHDOG AND BATTERY BACKUP |
| TC70EOA | MICROMASTER - SYSTEM SUPERVISOR WITH POWER SUPPLY MONITOR, WATCHDOG AND BATTERY BACKUP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TC-70.000MBD-T | 功能描述:標準時鐘振蕩器 70.000MHz 3.3V 25ppm -40C to 85C RoHS:否 制造商:AVX 產品:Standard Clock Oscillators 封裝 / 箱體:7 mm x 5 mm 頻率:75 MHz 頻率穩定性:50 PPM 電源電壓:2.5 V 負載電容: 端接類型:SMD/SMT 最小工作溫度:0 C 最大工作溫度:+ 70 C 輸出格式:LVDS 尺寸: 封裝:Reel 系列: |
| TC-70.000MBE-T | 制造商:TXC Corporation 功能描述:OSC MEMS 70.000 MHZ 3.3V SMD |
| TC-70.000MCD-T | 功能描述:標準時鐘振蕩器 70.000MHz 2.5V 25ppm -40C to 85C RoHS:否 制造商:AVX 產品:Standard Clock Oscillators 封裝 / 箱體:7 mm x 5 mm 頻率:75 MHz 頻率穩定性:50 PPM 電源電壓:2.5 V 負載電容: 端接類型:SMD/SMT 最小工作溫度:0 C 最大工作溫度:+ 70 C 輸出格式:LVDS 尺寸: 封裝:Reel 系列: |
| TC-70.000MCE-T | 制造商:TXC Corporation 功能描述:OSC MEMS 70.000 MHZ 2.5V SMD |
| TC-70.000MDD-T | 功能描述:標準時鐘振蕩器 70.000MHz 1.8V 25ppm -40C to 85C RoHS:否 制造商:AVX 產品:Standard Clock Oscillators 封裝 / 箱體:7 mm x 5 mm 頻率:75 MHz 頻率穩定性:50 PPM 電源電壓:2.5 V 負載電容: 端接類型:SMD/SMT 最小工作溫度:0 C 最大工作溫度:+ 70 C 輸出格式:LVDS 尺寸: 封裝:Reel 系列: |
發布緊急采購，3分鐘左右您將得到回復。