- 您現在的位置：買賣IC網 > PDF目錄98170 > TC647EOATR BRUSHLESS DC MOTOR CONTROLLER, PDSO8 PDF資料下載
參數資料
| 型號： | TC647EOATR |
| 元件分類： | 運動控制電子 |
| 英文描述： | BRUSHLESS DC MOTOR CONTROLLER, PDSO8 |
| 封裝： | 0.150 INCH, PLASTIC, SOIC-8 |
| 文件頁數： | 2/28頁 |
| 文件大小： | 478K |
| 代理商： | TC647EOATR |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
TC647
DS21447C-page 10
2002 Microchip Technology Inc.
5.1
Temperature Sensor Design
The temperature signal connected to VIN must output a
voltage in the range of 1.25V to 2.65V (typical) for 0%
to 100% of the temperature range of interest. The
circuit in Figure 5-2 illustrates a convenient way to
provide this signal.
FIGURE 5-2:
Temperature Sensing
Circuit.
Figure 5-2 illustrates a simple temperature dependent
voltage divider circuit. RT1 is a conventional 100 k @
25°C NTC thermistor, while R1 and R2 are standard
resistors. The supply voltage, VDD, is divided between
R2 and the parallel combination of RT1 and R1 (for con-
venience, the parallel combination of RT1 and R1 will
be referred to as RTEMP). The resistance of the ther-
mistor at various temperatures is obtained from the
manufacturer’s specifications. Thermistors are often
referred to in terms of their resistance at 25°C. Gener-
ally, the thermistor shown in Figure 5-2 is a non-linear
device with a negative temperature coefficient (also
linearize the thermistor temperature response and R2
is used to produce a positive temperature coefficient at
the VIN node. As an added benefit, this configuration
produces an output voltage delta of 1.4V, which is well
within the range of the VC(SPAN) specification of the
TC647. A 100 k
NTC thermistor is selected for this
application in order to keep IDIV at a minimum.
For the voltage range at VIN to be equal to 1.25V to
2.65V, the temperature range of this configuration is
0°C to 50°C. If a different temperature range is required
from this circuit, R1 should be chosen to equal the
resistance value of the thermistor at the center of this
new temperature range. It is suggested that a maxi-
mum temperature range of 50°C be used with this cir-
cuit due to thermistor linearity limitations. With this
change, R2 is adjusted according to the following
equations:
EQUATION
These two equations facilitate solving for the two
unknown variables, R1 and R2. More information about
Thermistors may be obtained from AN679, “Tempera-
ture Sensing Technologies”, and AN685, “Thermistors
in Single Supply Temperature Sensing Circuits”, which
can be downloaded from Microchip’s website at
www.microchip.com.
5.2
Minimum Fan Speed
A voltage divider on VMIN sets the minimum PWM duty
cycle and, thus, the minimum fan speed. As with the
VIN input, 1.25V to 2.65V corresponds to 0% to 100%
duty cycle. Assuming that fan speed is linearly related
to duty cycle, the minimum speed voltage is given by
the equation:
EQUATION
For example, if 2500 RPM equates to 100% fan speed,
and a minimum speed of 1000 RPM is desired, then
the VMIN voltage is:
EQUATION
The VMIN voltage may be set using a simple resistor
divider as shown in Figure 5-3. Per Section 1.0,
“Electrical Characteristics”, the leakage current at the
VMIN pin is no more than 1 A. It would be very
conservative to design for a divider current, IDIV, of
100 A. If VDD = 5.0V then;
EQUATION
R2 = 23.2 k
R1 = 100 k
RT1
NTC
Thermistor
100 k
@ 25C
IDIV
VIN
VDD
VDD x R2
RTEMP (T1) + R2
= V(T1)
RTEMP (T2) + R2
= V(T2)
VDD x R2
Where T1 and T2 are the chosen temperatures and
RTEMP is the parallel combination of the thermistor
and R1.
Minimum Speed
Full Speed
VMIN =
x (1.4V) + 1.25V
1000
2500
VMIN =
x (1.4V) + 1.25V = 1.81V
R1 + R2
IDIV = 1e–4A =
, therefore
5.0V
R1 + R2 =
= 50,000
= 50 k
1e–4A
5.0V
相關PDF資料 |
PDF描述 |
|---|---|
| TC647VUATR | BRUSHLESS DC MOTOR CONTROLLER, PDSO8 |
| TC647VOART | BRUSHLESS DC MOTOR CONTROLLER, PDSO8 |
| TC648EOA | BRUSHLESS DC MOTOR CONTROLLER, PDSO8 |
| TC648VOA | BRUSHLESS DC MOTOR CONTROLLER, PDSO8 |
| TC649BEPA | BRUSHLESS DC MOTOR CONTROLLER, PDIP8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TC647EPA | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:PWM Fan Speed Controller with FanSense Technology |
| TC647EUA | 功能描述:馬達/運動/點火控制器和驅動器 w/Fault Dtct RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| TC647EUATR | 功能描述:馬達/運動/點火控制器和驅動器 w/Fault Dtct RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| TC647VOA | 功能描述:馬達/運動/點火控制器和驅動器 w/Fault Dtct RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| TC647VOA | 制造商:Microchip Technology Inc 功能描述:Fan Management Controller IC Package/Cas |
發布緊急采購，3分鐘左右您將得到回復。