- 您現在的位置：買賣IC網 > PDF目錄383928 > TC3405A (Linear Technology Corporation) Standalone Linear Li-lon Battery Charger with Thermistor Input PDF資料下載
參數資料
| 型號： | TC3405A |
| 廠商： | Linear Technology Corporation |
| 元件分類： | 熱敏電阻 |
| 英文描述： | Standalone Linear Li-lon Battery Charger with Thermistor Input |
| 中文描述： | 獨立線性鋰離子電池充電器熱敏電阻輸入 |
| 文件頁數： | 9/20頁 |
| 文件大?。?/td> | 665K |
| 代理商： | TC3405A |
LTC4061
9
4061fa
OPERATIOU
The LTC4061 is designed to charge single cell lithium-ion
batteries. Using the constant current/constant voltage
algorithm, the charger can deliver up to 1A of charge
current with a final float voltage accuracy of ±0.35%. The
LTC4061 includes an internal P-channel power MOSFET
and thermal regulation circuitry. No blocking diode or
external sense resistor is required; thus, the basic charger
circuit requires only two external components.
Normal Operation
The charge cycle begins when the voltage at the V
CC
pin
rises above the UVLO level and a discharged battery is
connected to BAT. If the BAT pin voltage is below 2.9V,
the charger enters trickle charge mode. In this mode,
the LTC4061 supplies 1/10th of the programmed charge
current in order to bring the battery voltage up to a safe
level for full current charging.
Once the BAT pin voltage rises above 2.9V, the charger
enters constant current mode, where the programmed
charge current is supplied to the battery. When the BAT
pin approaches the final float voltage (4.2V), the LTC4061
enters constant voltage mode and the charge current
decreases as the battery becomes fully charged.
The LTC4061 offers several methods with which to ter-
minate a charge cycle. Connecting an external capacitor
to the TIMER pin activates an internal timer that stops
the charge cycle after the programmed time period has
elapsed. Grounding the TIMER pin and connecting a resis-
tor to the I
DET
pin causes the charge cycle to terminate
once the charge current falls below a set threshold when
the charger is in constant voltage mode. Connecting the
TIMER pin to V
CC
disables internal termination, allowing
external charge user termination through the
E
N input.
See Applications Information for more information on
charge termination methods.
Programming Charge Current
The charge current is programmed using a single resistor
from the PROG pin to ground. When the charger is in the
constant current mode, the voltage on the PROG pin is
1V. The battery charge current is 1000 times the current
out of the PROG pin. The program resistor and the charge
current are calculated by the following equations:
R
V
I
I
V
R
PROG
CHG
CHG
PROG
=
=
1000
1000
,
The charge current out of the BAT pin can be determined
at any time by monitoring the PROG pin voltage and ap-
plying the following equation:
V
R
PROG
I
BAT
PROG
=
1000
SmartStart
When the LTC4061 is initially powered on or brought
out of shutdown mode, the charger checks the battery
voltage. If the BAT pin is below the recharge threshold of
4.1V (which corresponds to approximately 80-90% battery
capacity), the LTC4061 enters charge mode and begins a
full charge cycle. If the BAT pin is above 4.1V, the LTC4061
enters standby mode and does not begin charging. This
feature reduces the number of unnecessary charge cycles,
prolonging battery life.
Automatic Recharge
When the charger is in standby mode, the LTC4061
continuously monitors the voltage on the BAT pin. When
the BAT pin voltage drops below 4.1V, the charge cycle is
automatically restarted and the internal timer is reset to
50% of the programmed charge time (if time termination
is being used). This feature eliminates the need for peri-
odic charge cycle initiations and ensures that the battery
is always fully charged. Automatic recharge is disabled
in user termination mode.
Thermal Regulation
An internal thermal feedback loop reduces the programmed
charge current if the die temperature attempts to rise
above a preset value of approximately 105°C. This feature
protects the LTC4061 from excessive temperature and
allows the user to push the limits of the power handling
capability of a given circuit board without risk of damaging
the LTC4061. The charge current can be set according to
typical (not worst-case) ambient temperatures with the
assurance that the charger will automatically reduce the
current in worst-case conditions.
相關PDF資料 |
PDF描述 |
|---|---|
| TC3405VQR | 16-Bit, Low Cost, Low Power Sigma-Delta A/D Converter |
| TC3405VPE | 16-Bit, Low Cost, Low Power Sigma-Delta A/D Converter |
| TC3405 | 16-Bit, Low Cost, Low Power Sigma-Delta A/D Converter |
| TC4420IMF713 | 6A High-Speed MOSFET Drivers |
| TC4420IOA | 6A High-Speed MOSFET Drivers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TC3405VPE | 功能描述:模數轉換器 - ADC 16-Bit Sigma-Delta RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| TC3405VQR | 功能描述:模數轉換器 - ADC 16-Bit Sigma-Delta RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| TC3405VQRTR | 功能描述:模數轉換器 - ADC 16-Bit Sigma-Delta RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| TC341 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:780X488 PIXEL CCD IMAGE SENSOR |
| TC341-20 | 功能描述:視頻 IC 780 X 488-Pixel CCD Image Sensor RoHS:否 制造商:Fairchild Semiconductor 工作電源電壓:5 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-28 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。