- 您現在的位置：買賣IC網 > PDF目錄361370 > TC32MEDB (TelCom Semiconductor, Inc.) CONNECTOR ACCESSORY PDF資料下載
參數資料
| 型號： | TC32MEDB |
| 廠商： | TelCom Semiconductor, Inc. |
| 英文描述： | CONNECTOR ACCESSORY |
| 中文描述： | ECONOMONITOR - 3針系統的監管機構與電源監視器和看門狗 |
| 文件頁數： | 4/4頁 |
| 文件大?。?/td> | 57K |
| 代理商： | TC32MEDB |
5-6
TELCOM SEMICONDUCTOR, INC.
so the time between toggles is less than one watchdog
timeout period. The strobe signal can be derived from
microprocessor address, data and/or control signals. Typi-
cal circuit examples are shown in Figure 4.
Resistor Value Selection
The values of R1 and R2 must be chosen to ensure a
valid low strobe level (V
STL
) on RS when the processor I/O
line is low. The use of 10k
,
±
5% tolerance resistors are
recommended. These values result in a nominal strobe level
of 2.5 on RS (min/max of 2.13V / 3.08V, assuming V
DD
=
5.0V
±
10%). Other resistor values can be used, so long as
the additive tolerances of the power supply and resistor
values result in a strobe that falls within V
STH
and V
STL
under
all additive tolerance conditions.
External Override Reset Control
A built-in debounce circuit allows a push-button switch
(PB) or other electronic signal to be wire-ORed to this pin as
an external RESET override control. The external
RESET is required to be an active low signal. Internally, this
input is timed to provide a minimum RESET pulse width of
500msec. Reference Figure 2.
Supply Monitor Noise Sensitivity
The TC32M is optimized for fast response to negative-
going changes in V
DD
. Systems with an inordinate amount
of electrical noise on V
DD
(such as systems using relays),
may require a 0.01
μ
F bypass capacitor to reduce detection
sensitivity. This capacitor should be installed as close to the
TC32M as possible to keep the capacitor lead length short.
DETAILED DESCRIPTION
The TC32M provides three important functions to safe-
guard stable processor operation: precision processor moni-
tor, watchdog sanity timer and external override reset
control.
Processor Monitor
The RS pin is immediately driven low any time V
DD
is
below the nominal threshold voltage. As a result, this pin is
LOW when power is initially applied, holding the processor
in its reset state. RS remains low for a minimum of 500msec
after V
DD
is within tolerance to allow the power supply and
processor to stabilize.
Watchdog Timer
The processor drives the RS pin with an input/output
(I/O) line in series with an resistor voltage divider to V
DD.
Pulling the bottom resistor of this divider low results in an
internal voltage change (strobe) sufficient to reset the watch-
dog timer, but above the V
IL
input threshold of the processor
RESET pin. The processor must continuously apply strobes
in this manner within a set period to verify proper software
execution. A momentary reset (500msec minimum) is gen-
erated by the TC32M if a hardware or software failure keeps
RS from being strobed within the watchdog timeout period.
This action typically initiates the processor's power-up rou-
tine. If the interruption persists, new reset pulses are gener-
ated each timeout period until RS is strobed. This timeout
period is typically 700msec.
The software routine that drives the RS strobe must be
in a section of the program that executes frequently enough
5V
5V
RESET
PO.1
RESET
MICRO-
CONTROLLER
MICRO-
PROCESSOR
R2,10k
MICROCONTROLLER EXAMPLE
RESET
DECODER
ADDRESS
RESET
R1, 10k
MICROPROCESSOR EXAMPLE
RS
TC32M
RS
TC32M
R1, 10k
R2, 10k
Figure 4. TC32M Hardware Connections (R1, R2 chosen to Meet V
STH
, V
STL
)
TC32M
ECONOMONITOR – 3-PIN SYSTEM SUPERVISOR
WITH POWER SUPPLY MONITOR AND WATCHDOG
相關PDF資料 |
PDF描述 |
|---|---|
| TC32MEZB | CONNECTOR ACCESSORY |
| TC3500 | 35A 5/16 TIN CAN TYPE PRESS-FIT DIODE |
| TC3501 | 35A 5/16 TIN CAN TYPE PRESS-FIT DIODE |
| TC3502 | 35A 5/16 TIN CAN TYPE PRESS-FIT DIODE |
| TC3503 | 35A 5/16 TIN CAN TYPE PRESS-FIT DIODE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TC32MEDB713 | 功能描述:監控電路 Economonitor RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| TC32MEZB | 功能描述:監控電路 Economonitor RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| TC32N3A32K7680 | 功能描述:OSCILLATOR 32.7680 KHZ 2.5V SMD RoHS:是 類別:晶體和振蕩器 >> 振蕩器 系列:TC32 標準包裝:1 系列:VG-4512CA 類型:VCXO 頻率:153.6MHz 功能:三態（輸出啟用） 輸出:LVPECL 電源電壓:3.3V 頻率穩定性:- 工作溫度:-40°C ~ 85°C 電流 - 電源（最大）:60mA 額定值:- 安裝類型:表面貼裝 尺寸/尺寸:0.276" L x 0.197" W（7.00mm x 5.00mm） 高度:0.071"（1.80mm） 封裝/外殼:6-SMD，無引線（DFN，LCC） 包裝:Digi-Reel® 電流 - 電源（禁用）（最大）:- 其它名稱:SER3790DKR |
| TC32N3C32K7680 | 功能描述:OSCILLATOR 32.7680 KHZ 2.5V SMD RoHS:是 類別:晶體和振蕩器 >> 振蕩器 系列:TC32 標準包裝:1 系列:VG-4512CA 類型:VCXO 頻率:153.6MHz 功能:三態（輸出啟用） 輸出:LVPECL 電源電壓:3.3V 頻率穩定性:- 工作溫度:-40°C ~ 85°C 電流 - 電源（最大）:60mA 額定值:- 安裝類型:表面貼裝 尺寸/尺寸:0.276" L x 0.197" W（7.00mm x 5.00mm） 高度:0.071"（1.80mm） 封裝/外殼:6-SMD，無引線（DFN，LCC） 包裝:Digi-Reel® 電流 - 電源（禁用）（最大）:- 其它名稱:SER3790DKR |
| TC32N3I32K7680 | 功能描述:OSCILLATOR 32.7680 KHZ 2.5V SMD RoHS:是 類別:晶體和振蕩器 >> 振蕩器 系列:TC32 標準包裝:1 系列:VG-4512CA 類型:VCXO 頻率:153.6MHz 功能:三態（輸出啟用） 輸出:LVPECL 電源電壓:3.3V 頻率穩定性:- 工作溫度:-40°C ~ 85°C 電流 - 電源（最大）:60mA 額定值:- 安裝類型:表面貼裝 尺寸/尺寸:0.276" L x 0.197" W（7.00mm x 5.00mm） 高度:0.071"（1.80mm） 封裝/外殼:6-SMD，無引線（DFN，LCC） 包裝:Digi-Reel® 電流 - 電源（禁用）（最大）:- 其它名稱:SER3790DKR |
發布緊急采購，3分鐘左右您將得到回復。