- 您現在的位置：買賣IC網 > PDF目錄98157 > TA8499F DISK DRIVE MOTOR CONTROLLER, 1.5 A, PDSO30 PDF資料下載
參數資料
| 型號： | TA8499F |
| 元件分類： | 運動控制電子 |
| 英文描述： | DISK DRIVE MOTOR CONTROLLER, 1.5 A, PDSO30 |
| 封裝： | 0.375 INCH, 1 MM PITCH, PLASTIC, SSOP-30 |
| 文件頁數： | 3/27頁 |
| 文件大?。?/td> | 711K |
| 代理商： | TA8499F |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
TA8499F/FG
11
2006-3-6
Hall element bias circuit
The hall element bias current is turned off when the driver IC is in standby state.
Make sure that the negative hall bias line is connected to the HB pin.
The remaining voltage is as follows;
VHB = 1.3[V] (typ.) at IHB = 20mA.
IHB must be set less than 20mA.
FG amp circuit
This circuit uses a hall element signal which is output to FGO after a Schmitt stage.
The FG amp has a hysteresis of 20[mVP-P] (typ.) and its output voltages are
High level
: VCC 0.5 to VCC[V]
Low level
: GND to 0.5[V] at IOFG = 10 A
The FG amp is active when it is in standby state. When the hall element signal is input, the FG signal is output.
相關PDF資料 |
PDF描述 |
|---|---|
| TA8552FN | SPECIALTY CONSUMER CIRCUIT, PDSO30 |
| TA8553FN | SPECIALTY ANALOG CIRCUIT, PDSO20 |
| TA8603P | AUDIO/VIDEO DEMODULATOR, PDIP16 |
| TA8611AN | AUDIO/VIDEO DEMODULATOR, PDIP20 |
| TA8648N | AUDIO/VIDEO DEMODULATOR, PDIP24 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TA8504 | 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:HIGH SPEED COMPARATOR |
| TA8504F | 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:HIGH SPEED COMPARATOR |
| TA8504FG | 制造商:Toshiba 功能描述:1 制造商:Toshiba 功能描述:1 Cut Tape |
| TA8505 | 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:SUPPLY VOLTAGE SUPERVISOR |
| TA8505P | 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:SUPPLY VOLTAGE SUPERVISOR |
發布緊急采購，3分鐘左右您將得到回復。