參數資料
型號: TA1307P
廠商: Toshiba Corporation
英文描述: Integrated Circuit For Standby Power-Supply Control
中文描述: 集成電路,備用電源控制
文件頁數: 3/12頁
文件大?。?/td> 124K
代理商: TA1307P
TA1307P
2002-02-12
3
With outputting burst switching control pulse from IC, burst enegize of the TRANS is carried out.
Voltage stabilized also at the time of a light load can be supplied.
It is the optimum IC for constituting the power-supply system for minute electric-power supply.
By this IC, the burst time of switching control pulse is decided by level of output ripple of a power-supply system.
As for the terminal 4 which is carrying out the monitor of the power-supply output-voltage value, another side is
connected to the comparator.
The standard voltage value of this comparator has hysterisis, 2.5 V and 3 V fixation. (inside IC)
Since output DC voltage of a power supply is stabilized, power-supply output voltage is detected and it feedbacks
for the terminal 4 (FB IN terminal).
When the voltage value of a terminal 4 tends to become more than 3 V, switching control pulse of a terminal 7
(pulse out) is stopped.
If pulse is stooped, in order not to control power-supply TRANS, it will stop supplying energy supplied to the output
of a power supply, and the output DC voltage of a power-supply will descend.
If output DC voltage tends to become less than (V/2.5), switching control pulse of a terminal 7 (pulse out) will be
outputted.
Power-supply TRANS is made to drive and PULSE supplies energy to a power-supply output.
Then, output DC voltage rises.
Burst electric supply is realized by repeating the above-mentioned operation.
Hereafter, calculation using ripple level as an example
Voltage of V
out
and the terminal 2 is set output DC voltage to V
ref
.
V
out
V
z
V
F
1/CTR R2/R1 V
ref
*CTR I
C
/I
F
*I
Z
I
F
I
S
, R3 is set up.
For example, R1 10 k , R2 R3 1 k , CTR about 1, V
z
3.9 V, V
F
0.7 V
V
ref
(minimum) 2.5 V fixation and V
ref
(maximum) 3 V fixation.
Calculation
V
out
(minimum) 4.85 V
V
out
(maximum) 4.9 V.
Ripple in an output is 0.05 V.
Internal oscillation circuit for obtaining output PULSE is built in.
Oscillation frequency of output PULSE can be set up by outside attachment resistance to a terminal 2.
Duty about 50% of output PULSE has been obtained.
Oscillation frequency is calculation from f i/2 CV (Hz), I 1 (V) /R/10, and it will be set to 25 kHz, if 20 k is
attached to a terminal 2 outside.
Terminal voltage and R are outside attachment resistance in 1 (V).
10 is a current ratio, sets current of a terminal 2 to 1/10, and makes it the charge/discharge current of a internal
50 pF capacitor. C 50 (pF) (built-in capacitor value) V 2 (V) (oscillation amplitude)
Figure 2 Ripple Voltage Establish
(example)
4
V
out
V
cc
I
C
Is
R
I
F
I
z
R2
FB
R
V
z
V
F
FB comparater
V
ref
2.5 V/3 V
相關PDF資料
PDF描述
TA1310ANG Zener Diode; Application: Low noise; Pd (mW): 250; Vz (V): 3.1 to 3.5; Condition Iz at Vz (mA): 0.5; C (pF) max: -; Condition VR at C (V):   ESD (kV) min: -; Package: DO-35
TA1317AFG Zener Diode; Application: Low noise; Pd (mW): 250; Vz (V): 3.4 to 3.8; Condition Iz at Vz (mA): 0.5; C (pF) max: -; Condition VR at C (V):   ESD (kV) min: -; Package: DO-35
TA1317ANG Zener Diode; Application: Low noise; Pd (mW): 250; Vz (V): 3.7 to 4.1; Condition Iz at Vz (mA): 0.5; C (pF) max: -; Condition VR at C (V):   ESD (kV) min: -; Package: DO-35
TA1317AN Deflection Processor IC for TV
TA1318AFG Zener Diode; Application: Low noise; Pd (mW): 250; Vz (V): 4.0 to 4.4; Condition Iz at Vz (mA): 0.5; C (pF) max: -; Condition VR at C (V):   ESD (kV) min: -; Package: DO-35
相關代理商/技術參數
參數描述
TA1307PG() 制造商:Toshiba America Electronic Components 功能描述:
TA131 制造商:pico Technology 功能描述:Probe; Oscilloscope; 250 MHz; 1.2 m; 1:1/10:1
TA131007 制造商:Fibox 功能描述:Bulk
TA1310AN 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:NTSC VIDEO, CHROMA, DEFLECTION, AND DISTORTION COMPENSATION IC (WITH YUV INTERFACE AND ACB)
TA1310ANG 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:NTSC VIDEO, CHROMA, DEFLECTION, AND DISTORTION COMPENSATION IC (WITH YUV INTERFACE AND ACB)