- 您現在的位置：買賣IC網 > PDF目錄373534 > T89C51RD2-SLBI-L (Atmel Corp.) 0 to 40MHz Flash Programmable 8-bit Microcontroller PDF資料下載
參數資料
| 型號： | T89C51RD2-SLBI-L |
| 廠商： | Atmel Corp. |
| 英文描述： | 0 to 40MHz Flash Programmable 8-bit Microcontroller |
| 中文描述： | 0至40MHz可編程閃存8位微控制器 |
| 文件頁數： | 22/170頁 |
| 文件大?。?/td> | 1927K |
| 代理商： | T89C51RD2-SLBI-L |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁
22
A/T89C51CC01
4129L–CAN–08/05
Warm Reset
To achieve a valid reset, the reset signal must be maintained for at least 2 machine
cycles (24 oscillator clock periods) while the oscillator is running. The number of clock
periods is mode independent (X2 or X1).
Watchdog Reset
As detailed in Section “PCA Watchdog Timer”, page 127, the WDT generates a 96-clock
period pulse on the RST pin. In order to properly propagate this pulse to the rest of the
application in case of external capacitor or power-supply supervisor circuit, a 1K
Ω
resis-
tor must be added as shown Figure 8.
Figure 8.
Reset Circuitry for WDT reset out usage
Reset Recommendation
to Prevent Flash
Corruption
An example of bad initialization situation may occur in an instance where the bit
ENBOOT in AUXR1 register is initialized from the hardware bit BLJB upon reset. Since
this bit allows mapping of the bootloader in the code area, a reset failure can be critical.
If one wants the ENBOOT cleared in order to unmap the boot from the code area (yet
due to a bad reset) the bit ENBOOT in SFRs may be set. If the value of Program
Counter is accidently in the range of the boot memory addresses then a flash access
(write or erase) may corrupt the Flash on-chip memory.
It is recommended to use an external reset circuitry featuring power supply monitoring to
prevent system malfunction during periods of insufficient power supply voltage (power
supply failure, power supply switched off).
Idle Mode
Idle mode is a power reduction mode that reduces the power consumption. In this mode,
program execution halts. Idle mode freezes the clock to the CPU at known states while
the peripherals continue to be clocked. The CPU status before entering Idle mode is
preserved, i.e., the program counter and program status word register retain their data
for the duration of Idle mode. The contents of the SFRs and RAM are also retained. The
status of the Port pins during Idle mode is detailed in Table 14.
Entering Idle Mode
To enter Idle mode, you must set the IDL bit in PCON register (see Table 15). The
T89C51CC01 enters Idle mode upon execution of the instruction that sets IDL bit. The
instruction that sets IDL bit is the last instruction executed.
Note:
If IDL bit and PD bit are set simultaneously, the T89C51CC01 enters Power-down mode.
Then it does not go in Idle mode when exiting Power-down mode.
Exiting Idle Mode
There are two ways to exit Idle mode:
1.
Generate an enabled interrupt.
–
Hardware clears IDL bit in PCON register which restores the clock to the
CPU. Execution resumes with the interrupt service routine. Upon completion
R
R
RST
VSS
To CPU core
and peripherals
VDD
+
VSS
VDD
RST
1K
To other
on-board
circuitry
相關PDF資料 |
PDF描述 |
|---|---|
| T89C51RD2-RLBI-L | 0 to 40MHz Flash Programmable 8-bit Microcontroller |
| T89C51RD2-SLBI-M | 0 to 40MHz Flash Programmable 8-bit Microcontroller |
| T89C51RD2-RLBI-M | 0 to 40MHz Flash Programmable 8-bit Microcontroller |
| T89C51RC2-SLBIL | 8-bit Microcontroller with 16 Kbytes/ 32 Kbytes FLASH |
| T89C51RC2-RLBIL | 8-bit Microcontroller with 16 Kbytes/ 32 Kbytes FLASH |
相關代理商/技術參數 |
參數描述 |
|---|---|
| T89C51RD2-SLBI-M | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:0 to 40MHz Flash Programmable 8-bit Microcontroller |
| T89C51RD2-SLFCL | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:0 to 40 MHz Flash Programmable 8-bit Microcontroller |
| T89C51RD2-SLFC-L | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:0 to 40MHz Flash Programmable 8-bit Microcontroller |
| T89C51RD2-SLFC-M | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:0 to 40MHz Flash Programmable 8-bit Microcontroller |
| T89C51RD2-SLFI-L | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:0 to 40MHz Flash Programmable 8-bit Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。