- 您現在的位置：買賣IC網 > PDF目錄373534 > T89C51RD2-RLUI-L (Atmel Corp.) 0 to 40MHz Flash Programmable 8-bit Microcontroller PDF資料下載
參數資料
| 型號： | T89C51RD2-RLUI-L |
| 廠商： | Atmel Corp. |
| 英文描述： | 0 to 40MHz Flash Programmable 8-bit Microcontroller |
| 中文描述： | 0至40MHz可編程閃存8位微控制器 |
| 文件頁數： | 33/170頁 |
| 文件大?。?/td> | 1927K |
| 代理商： | T89C51RD2-RLUI-L |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁當前第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁
33
A/T89C51CC01
4129L–CAN–08/05
EEPROM Data
Memory
The 2-Kbyte on-chip EEPROM memory block is located at addresses 0000h to 07FFh of
the XRAM/XRAM memory space and is selected by setting control bits in the EECON
register. A read in the EEPROM memory is done with a MOVX instruction.
A physical write in the EEPROM memory is done in two steps: write data in the column
latches and transfer of all data latches into an EEPROM memory row (programming).
The number of data written on the page may vary from 1 up to 128 Bytes (the page
size). When programming, only the data written in the column latch is programmed and
a ninth bit is used to obtain this feature. This provides the capability to program the
whole memory by Bytes, by page or by a number of Bytes in a page. Indeed, each ninth
bit is set when the writing the corresponding byte in a row and all these ninth bits are
reset after the writing of the complete EEPROM row.
Write Data in the Column
Latches
Data is written by byte to the column latches as for an external RAM memory. Out of the
11 address bits of the data pointer, the 4 MSBs are used for page selection (row) and 7
are used for byte selection. Between two EEPROM programming sessions, all the
addresses in the column latches must stay on the same page, meaning that the 4 MSB
must no be changed.
The following procedure is used to write to the column latches:
Save and disable interrupt.
Set bit EEE of EECON register
Load DPTR with the address to write
Store A register with the data to be written
Execute a MOVX @DPTR, A
If needed loop the three last instructions until the end of a 128 Bytes page
Restore interrupt.
Note:
The last page address used when loading the column latch is the one used to select the
page programming address.
Programming
The EEPROM programming consists of the following actions:
writing one or more Bytes of one page in the column latches. Normally, all Bytes
must belong to the same page; if not, the last page address will be latched and the
others discarded.
launching programming by writing the control sequence (50h followed by A0h) to the
EECON register.
EEBUSY flag in EECON is then set by hardware to indicate that programming is in
progress and that the EEPROM segment is not available for reading.
The end of programming is indicated by a hardware clear of the EEBUSY flag.
Note:
The sequence 5xh and Axh must be executed without instructions between then other-
wise the programming is aborted.
Read Data
The following procedure is used to read the data stored in the EEPROM memory:
Save and disable interrupt
Set bit EEE of EECON register
Load DPTR with the address to read
Execute a MOVX A, @DPTR
Restore interrupt
相關PDF資料 |
PDF描述 |
|---|---|
| T89C51RD2-SLUI-M | 0 to 40MHz Flash Programmable 8-bit Microcontroller |
| T89C51RD2-RLUI-M | 0 to 40MHz Flash Programmable 8-bit Microcontroller |
| T89C51RD2-SLRC-L | 0 to 40MHz Flash Programmable 8-bit Microcontroller |
| T89C51RD2-RLRC-L | 0 to 40MHz Flash Programmable 8-bit Microcontroller |
| T89C51RD2-SLRC-M | 0 to 40MHz Flash Programmable 8-bit Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| T89C51RD2-RLUI-M | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:0 to 40MHz Flash Programmable 8-bit Microcontroller |
| T89C51RD2-RLVCL | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:0 to 40 MHz Flash Programmable 8-bit Microcontroller |
| T89C51RD2-RLVC-L | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:0 to 40MHz Flash Programmable 8-bit Microcontroller |
| T89C51RD2-RLVCM | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:0 to 40 MHz Flash Programmable 8-bit Microcontroller |
| T89C51RD2-RLVC-M | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:0 to 40MHz Flash Programmable 8-bit Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。