- 您現在的位置：買賣IC網 > PDF目錄373518 > SX28AC75 (Electronic Theatre Controls, Inc.) Configurable Communications Controllers with EE/Flash Program Memory, In-System Programming Capability and On-Chip Debug PDF資料下載
參數資料
| 型號： | SX28AC75 |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | Configurable Communications Controllers with EE/Flash Program Memory, In-System Programming Capability and On-Chip Debug |
| 中文描述： | 配置通信控制器與電子工程/閃存程序存儲器，在系統編程能力和片上調試 |
| 文件頁數： | 34/52頁 |
| 文件大?。?/td> | 688K |
| 代理商： | SX28AC75 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁當前第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
2000 Scenix Semiconductor, Inc. All rights reserved.
- 34 -
www.scenix.com
SX18AC/SX20AC/SX28AC/SX18AC75/SX20AC75/SX28AC75
15.13
Comparison and Conditional Branch
Instructions
The instruction set includes instructions such as DECSZ
fr (decrement file register and skip if zero), INCSZ fr
(increment file register and skip if zero), SNB bit (bit test
file register and skip if bit clear), and SB bit (bit test file
register and skip if bit set). These instructions will cause
the next instruction to be skipped if the tested condition is
true. If a skip instruction is immediately followed by a
PAGE or BANK instruction (and the tested condition is
true) then two instructions are skipped and the operation
consumes three cycles. This is useful for conditional
branching to another page where a PAGE instruction pre-
cedes a JMP. If several PAGE and BANK instructions
immediately follow a skip instruction then they are all
skipped plus the next instruction and a cycle is consumed
for each.
15.14
Logical Instruction
The instruction set contain a full complement of the logi-
cal instructions (AND, OR, Exclusive OR), with the W
register and a selected memory location (using either
direct or indirect addressing) serving as the two oper-
ands.
15.15
Shift and Rotate Instructions
The instruction set includes instructions for left or right
rotate-through-carry.
15.16
Complement and SWAP
The device can perform one’s complement operation on
the file register (fr) and W register. The MOV W,<>fr
instruction performs nibble-swap on the fr and puts the
value into the W register.
15.17
Key to Abbreviations and Symbols
Symbol
Description
W
Working register
File register (memory-mapped register in the
range of 00h to FFh)
Lower eight bits of program counter (file regis-
ter 02h)
STATUS
STATUS register (file register 03h)
File Select Register (file register 04h)
Carry bit in STATUS register (bit 0)
Digit Carry bit in STATUS register (bit 1)
Zero bit in STATUS register (bit 2
Power Down bit in STATUS register (bit 3)
Watchdog Timeout bit in STATUS register (bit
4)
PA2:PA0
Page select bits in STATUS register (bits 7:5)
OPTION
OPTION register (not memory-mapped)
Watchdog Timer register (not memory-
mapped)
MODE register (not memory-mapped)
Port control register pointer (RA, RB, or RC)
Non-memory-mapped register designator
File register address bit in opcode
Constant value bit in opcode
Numerical value bit in opcode
Bit position selector bit in opcode
File register / bit selector separator in assem-
bly language instruction
Immediate literal designator in assembly lan-
guage instruction
Literal value in assembly language instruction
8-bit address in assembly language instruction
9-bit address in assembly language instruction
12-bit address in assembly language instruc-
tion
Logical 1’s complement
Logical OR
Logical exclusive OR
Logical AND
Swap high and low nibbles (4-bit segments)
Rotate left through carry bit
Rotate right through carry bit
Decrement file register
Increment file register
fr
PC
FSR
C
DC
Z
PD
TO
WDT
MODE
rx
!
f
k
n
b
.
#
lit
addr8
addr9
addr12
/
|
^
&
<>
<<
>>
- -
++
相關PDF資料 |
PDF描述 |
|---|---|
| SX18AC | Configurable Communications Controllers with EE/Flash Program Memory, In-System Programming Capability and On-Chip Debug |
| SX20AC | Configurable Communications Controllers with EE/Flash Program Memory, In-System Programming Capability and On-Chip Debug |
| SX20AC75 | Configurable Communications Controllers with EE/Flash Program Memory, In-System Programming Capability and On-Chip Debug |
| SX28 | Configurable Communications Controllers with EE/Flash Program Memory, In-System Programming Capability and On-Chip Debug |
| SX28AC | Configurable Communications Controllers with EE/Flash Program Memory, In-System Programming Capability and On-Chip Debug |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SX28AC75DP | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:IC-8-BIT MCU |
| SX28AC75-I/DP | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Configurable Communications Controllers with EE/Flash Program Memory, In-System Programming Capability and On-Chip Debug |
| SX28AC75-I/PQ | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Configurable Communications Controllers with EE/Flash Program Memory, In-System Programming Capability and On-Chip Debug |
| SX28AC75-I/SO | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Configurable Communications Controllers with EE/Flash Program Memory, In-System Programming Capability and On-Chip Debug |
| SX28AC75-I/SS | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Configurable Communications Controllers with EE/Flash Program Memory, In-System Programming Capability and On-Chip Debug |
發布緊急采購，3分鐘左右您將得到回復。