參數資料
型號： SX21V001-Z4
英文描述： LCD GRAPHIC MODULE
中文描述： 液晶圖形模塊
文件頁數： 23/27頁
文件大?。?/td> 173K
代理商： SX21V001-Z4
3284PS 2711 - SX21V001-Z4 - 3
June 29, '99
11-2/3
11.3 POWER ON SEQUENCE
Input signals should not be applied to LCD module before power supply voltage is applied and
reaches to specified voltage (3.3
±
0.15V).
If the above sequence is not kept, C-MOS LSIs of LCD module may be damaged due to latch up
phenomenon.
11.4 HANDLING PRECAUTIONS
(1) Since the polarizer on the top, and the aluminum plate on the bottom tend to be easily damaged,
they should be handled w ith full care so as not to get them touched, pushed or rubbed by a piece
on glass, tw eezers and anything else w hich are harder than a pencil lead 3H.
(2) As the adhesives used for adhering upper/lower polarizers and aluminum plate are made of
organic substances which will be deteriorated by a chemical reaction w ith such chemicals as
acetone, tuluene, ethanole and isopropylalcohol. The following solvents are recommended for
use : Normal hexane
Please contact us w hen it is necessary for you to use chemicals other than the above.
(3) Lightly w ipe to clean the dirty surface w ith absorbent cotton or other soft material like chamois,
soaked in the recommended chemicals w ithout scrubbing it hardly.
Always w ipe the surface horizontally or vertically. Never give a wipe in a circle. To prevent
the display surface from damage and keep the appearance in good state, it is sufficient, in general,
to wipe it with absorbent cotton.
(4) Immediately w ipe off saliva or w ater drop attached on the display area because it may cause
deformation or faded color.
(5) Fogy dew deposited on the surface may cause a damage, stain or dirt to the polarizer.
When you need to take out the LCD module from some place at low temperature for test, etc.
It is required to be w armed them up to be temperature higher than room temperature before taking
them out.
(6) Touching the display area or I/F pins w ith bare hands or contaminating them are prohibited,
because the stain on the display area and poor insulation betw een terminals are often caused by
being touched with bare hands.
(Some cosmetics are detrimental to polarizers.)
(7) In general, the glass is fragile so that it, especially on its periphery, tends to be cracked or
chipped in handling. Please do not give the LCD module sharp shocks caused by falling etc.
(8) Maximum pressure to the surface must be less than 1.96
×
10
4
Pa (0.2kgf/cm
2
).
And if the pressure area is less than 1cm
2
, maximum pressure must be less than 1.96N (0.2kgf).
(9) Since the metal width is narrow on these locations (see page 9-1/3), please be careful w ith
handling.
Displays,
Hitachi, Ltd.
Sh.
No.
Page
Date
相關PDF資料
PDF描述
SXA289T1 Analog IC
SXA289T2 Analog IC
SXH189TR1 Analog IC
SXH189TR2 Analog IC
SXH1TR1 Analog IC
相關代理商/技術參數
參數描述
SX21V001-Z4A 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:CUSTOMERS ACCEPTANCE SPECIFICATIONS SX21V001-Z4A
SX22 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:5 WATT VOLTAGE REGULATOR
SX222A 制造商:CDE 功能描述:_
SX2236EGT1 制造商:Freescale Semiconductor 功能描述:
SX224 制造商:Mallory Sonalert Products Inc 功能描述:Cap Film 0.0024uF 500V PS 5% (10.2 X 17mm) Axial 70°C
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*