- 您現在的位置：買賣IC網 > PDF目錄373518 > SX20AC (Electronic Theatre Controls, Inc.) Configurable Communications Controllers with EE/Flash Program Memory, In-System Programming Capability and On-Chip Debug PDF資料下載
參數資料
| 型號： | SX20AC |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | Configurable Communications Controllers with EE/Flash Program Memory, In-System Programming Capability and On-Chip Debug |
| 中文描述： | 配置通信控制器與電子工程/閃存程序存儲器，在系統編程能力和片上調試 |
| 文件頁數： | 32/52頁 |
| 文件大小： | 688K |
| 代理商： | SX20AC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁當前第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
2000 Scenix Semiconductor, Inc. All rights reserved.
- 32 -
www.scenix.com
SX18AC/SX20AC/SX28AC/SX18AC75/SX20AC75/SX28AC75
15.10.2 Page Jump Operation
When a JMP instruction is executed and the intended
destination is on a different page, the page select bits
must be initialized with appropriate values to point to the
desired page before the jump occurs. This can be done
easily with SETB and CLRB instructions or by writing a
value to the STATUS register. The device also has the
PAGE instruction, which automatically selects the page in
a single-cycle execution.
Note: “N” must be 0, 1, 2, or 3.
15.10.3 Call Operation
The following happens when a CALL instruction is exe-
cuted:
The current value of the program counter is increment-
ed and pushed onto the top of the stack.
The lower eight bits of the label address are copied into
the lower eight bits of the program counter.
The ninth bit of the Program Counter is cleared to zero.
The page select bits (in STATUS register) are copied
into the upper two bits of the Program Counter.
This means that the call destination must start in the
lower half of any page. For example, 00h-0FFh, 200h-
2FFh, 400h-4FFh, etc.
15.10.4 Page Call Operation
When a subroutine that resides on a different page is
called, the page select bits must contain the proper val-
ues to point to the desired page before the call instruction
is executed. This can be done easily using SETB and
CLRB instructions or writing a value to the STATUS reg-
ister. The device also has the PAGE instruction, which
automatically selects the page in a single-cycle execu-
tion.
Note:“N” must be 0, 1, 2, or 3.
15.11
The device has several instructions for returning from
subroutines and interrupt service routines. The return
from subroutine instructions are RET (return without
affecting W), RETP (same as RET but affects PA1:PA0),
RETI (return from interrupt), RETIW (return and add W to
RTCC), and RETW #literal (return and place literal in W).
The literal serves as an immediate data value from mem-
ory. This instruction can be used for table lookup opera-
tions. To do table lookup, the table must contain a string
of RETW #literal instructions. The first instruction just in
front of the table calculates the offset into the table. The
table can be used as a result of a CALL.
Return Instructions
PAGE N
STATUS<6:5>
JMP LABEL
PC<10:9>
PC<8:0>
STATUS<6:5>
0
CALL LABEL
PC<10:9>
PC<8>
PC<7:0>
PAGE N
STATUS<6:5>
0
CALL LABEL
PC<10:9>
PC<8>
PC<7:0>
相關PDF資料 |
PDF描述 |
|---|---|
| SX20AC75 | Configurable Communications Controllers with EE/Flash Program Memory, In-System Programming Capability and On-Chip Debug |
| SX28 | Configurable Communications Controllers with EE/Flash Program Memory, In-System Programming Capability and On-Chip Debug |
| SX28AC | Configurable Communications Controllers with EE/Flash Program Memory, In-System Programming Capability and On-Chip Debug |
| SX18AC75 | Configurable Communications Controllers with EE/Flash Program Memory, In-System Programming Capability and On-Chip Debug |
| SX48BD | Configurable Communications Controllers with EE/Flash Program Memory, In-System Programming Capability, and On-Chip Debug |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SX20AC/SS | 功能描述:8位微控制器 -MCU 75MHz 2048x12 Flash 136 RAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| SX20AC/SS-G | 功能描述:8位微控制器 -MCU RISC 75MHz 8bit timer RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| SX20AC100-I/DP | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Configurable Communications Controllers with EE/Flash Program Memory, In-System Programming Capability and On-Chip Debug |
| SX20AC100-I/PQ | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Configurable Communications Controllers with EE/Flash Program Memory, In-System Programming Capability and On-Chip Debug |
| SX20AC100-I/SO | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Configurable Communications Controllers with EE/Flash Program Memory, In-System Programming Capability and On-Chip Debug |
發布緊急采購，3分鐘左右您將得到回復。