- 您現在的位置：買賣IC網 > PDF目錄383844 > STPCD0113BTC3 32-Bit Microprocessor PDF資料下載
參數資料
| 型號： | STPCD0113BTC3 |
| 元件分類： | 32位微控制器 |
| 英文描述： | 32-Bit Microprocessor |
| 中文描述： | 32位微處理器 |
| 文件頁數： | 19/61頁 |
| 文件大?。?/td> | 1007K |
| 代理商： | STPCD0113BTC3 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁
PIN DESCRIPTION
Issue 2.2 - October 13, 2000
19/61
ISAOE#
Bidirectional OE Control. This signal con-
trols the OE signal of the external transceiver that
connects the IDE DD bus and ISA SA bus.
GPIOCS#
I/O General Purpose Chip Select 1.
This output signal is used by the external latch on
ISA bus to latch the data on the SD[7:0] bus. The
latch can be used by the PMU unit to control the
external peripheral devices to power down or any
other desired function.
This pin is also serves as a strap input during re-
set.
2.2.9.
IDE CONTROL
PIRQ
Primary Interrupt Request.Interrupt request
from primary IDE channel.
SIRQ
Secondary Interrupt Request. Interrupt re-
quest from secondary IDE channel.
PDRQ
Primary DMA Request. DMA request from
primary IDE channel.
SDRQ
Secondary DMA Request. DMA request
from secondary IDE channel.
PDACK#
Primary DMA Acknowledge.DMA ac-
knowledge to primary IDE channel.
SDACK#
Secondary DMA Acknowledge.DMA
acknowledge to secondary IDE channel.
PIOR#
Primary I/O Read. Primary channel read.
Active low output.
PIOW#
Primary I/O Write. Primary channel write.
Active low output.
SIOR#
Secondary I/O Read. Secondary channel
read. Active low output.
SIOW#
Secondary I/O Write.Secondary channel
write. Active low output.
2.2.10. X-BUS INTERFACE PINS / IDE DATA
RMRTCCS# / DD[15]
ROM/Real Time Clock Chip
Select. This pin is a multi-function pin. When
ISAOE# is active, this signal is used as RM-
RTCCS#. This signal is asserted if a ROM access
is decoded during a memory cycle. It should be
combined with MEMR# or MEMW# signals to
properly access the ROM. During an I/O cycle,
this signal is asserted if access to the Real Time
Clock (RTC) is decoded. It should be combined
with IOR#+ or IOW# signals to properly access the
real time clock.
When ISAOE# is inactive, this signal is used as
IDE DD[15] signal.
This signal must be ORed externally with ISAOE#
and is then connected to ROM and RTC. An
LS244 or equivalent function can be used if OE# is
connected to ISAOE# and the output is provided
with a weak pull-up resistor.
KBCS# / DD[14]
Keyboard Chip Select. This pin
is a multi-function pin. When ISAOE# is active,
this signal is used as KBCS#. This signal is assert-
ed if a keyboard access is decoded during a I/O
cycle.
When ISAOE# is inactive, this signal is used as
IDE DD[14] signal.
This signal must be ORed externally with ISAOE#
and is then connected to the keyboard. An LS244
or equivalent function can be used if OE# is con-
nected to ISAOE# and the output is provided with
a weak pull-up resistor.
RTCRW# / DD[13]
Real Time Clock RW. This pin
is a multi-function pin. When ISAOE# is active,
this signal is used as RTCRW#. This signal is as-
serted for any I/O write to port 71H.
When ISAOE# is inactive, this signal is used as
IDE DD[13] signal.
This signal must be ORed externally with ISAOE#
and then connected to the RTC. An LS244 or
equivalent function can be used if OE# is connect-
ed to ISAOE# and the output is provided with a
weak pull-up resistor.
RTCDS# / DD[12]
Real Time Clock DS. This pin is
a multi-function pin. When ISAOE# is active, this
signal is used as RTCDS. This signal is asserted
for any I/O read to port 71H.
When ISAOE# is inactive, this signal is used as
IDE DD[12] signal.
This signal must be ORed externally with ISAOE#
and is then connected to RTC. An LS244 or equiv-
alent function can be used if OE# is connected to
ISAOE# and the output is provided with a weak
pull-up resistor.
2.2.11. IPC
IRQ_MUX[3:0]
Multiplexed Interrupt Request.
These are the ISA bus interrupt signals. They are
to be encoded before connection to the STPC Cli-
ent using ISACLK and ISACLKX2 as the input se-
lection strobes.
Note that IRQ8B, which by convention is connect-
ed to the RTC, is inverted before being sent to the
interrupt controller, so that it may be connected di-
rectly to the IRQ pin of the RTC.
PCI_INT[3:0]
PCI Interrupt Request. These are
the PCI bus interrupt signals. They are to be en-
coded before connection to the STPC Client using
相關PDF資料 |
PDF描述 |
|---|---|
| STPCI01 | STPC INDUSTRIAL / PC COMPATIBLE EMBEDED MICROPROCESSOR |
| STPCI2 | STPC ATLAS DATASHEET / X86 CORE PC COMPATIBLE SYSTEM-ON-CHIP FOR TERMINALS |
| STPCI2GDYI | PERIPHERAL (MULTIFUNCTION) CONTROLLER |
| STPCI2HDYC | PERIPHERAL (MULTIFUNCTION) CONTROLLER |
| STPCI2HEYI | PERIPHERAL (MULTIFUNCTION) CONTROLLER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| STPCD0166BTA3 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:PC Compatible Embedded Microprocessor |
| STPCD0166BTC3 | 制造商:STMicroelectronics 功能描述:MPU STPC RISC 64-Bit 66MHz 388-Pin BGA |
| STPCD0166BTI3 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:PC Compatible Embedded Microprocessor |
| STPCD0175BTC3 | 功能描述:微處理器 - MPU 75MHz x86 Embedded RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324 |
| STPCD0175BTI3 | 功能描述:微處理器 - MPU 75MHz x86 Embedded RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324 |
發布緊急采購，3分鐘左右您將得到回復。