參數資料
型號: STM32F103T6U6AXX
廠商: STMICROELECTRONICS
元件分類: 微控制器/微處理器
英文描述: 32-BIT, FLASH, 72 MHz, RISC MICROCONTROLLER, PQCC36
封裝: 6 X 6 MM, 0.50 MM PITCH, ROHS COMPLIANT, VFQFPN-36
文件頁數: 19/83頁
文件大?。?/td> 998K
代理商: STM32F103T6U6AXX
Pin descriptions
STM32F103x6, STM32F103x8, STM32F103xB
A4
46
62
96
-
PB9
I/O FT
PB9
I2C1_SDA /
CANTX
D4
-
97
-
PE0
I/O FT
PE0
TIM4_ETR(6)
C4
-
98
-
PE1
I/O FT
PE1
E5
47
63
99
36
VSS_3
SVSS_3
F5
48
64
100
1
VDD_3
SVDD_3
1.
I = input, O = output, S = supply, HiZ = high impedance.
2.
FT = 5 V tolerant.
3.
Function availability depends on the chosen device. For devices having reduced peripheral counts, it is always the lower
number of peripheral that is included. For example, if a device has only one SPI and two USARTs, they will be called SPI1
and USART1 & USART2, respectively. Refer to Table 2 on page 8.
4.
PC13, PC14 and PC15 are supplied through the power switch, and so their use in output mode is limited: they can be used
only in output 2 MHz mode with a maximum load of 30 pF and only one pin can be put in output mode at a time.
5.
Main function after the first backup domain power-up. Later on, it depends on the contents of the Backup registers even
after reset (because these registers are not reset by the main reset). For details on how to manage these IOs, refer to the
Battery backup domain and BKP register description sections in the STM32F10xxx reference manual, available from the
STMicroelectronics website: www.st.com.
6.
Available only on devices with a Flash memory density equal or higher than 64 Kbytes.
7.
This alternate function can be remapped by software to some other port pins (if available on the used package). For more
details, refer to the Alternate function I/O and debug configuration section in the STM32F10xxx reference manual, available
from the STMicroelectronics website: www.st.com.
8.
The pins number 2 and 3 in the VFQFPN36 package, and 5 and 6 in the LQFP48 and LQFP64 packages are configured as
OSC_IN/OSC_OUT after reset, however the functionality of PD0 and PD1 can be remapped by software on these pins. For
the LQFP100 package, PD0 and PD1 are available by default, so there is no need for remapping. For more details, refer to
the Alternate function I/O and debug configuration section in the STM32F10xxx reference manual.
The use of PD0 and PD1 in output mode is limited as they can only be used at 50 MHz in output mode.
Table 4.
Pin definitions (continued)
Pins
Pin name
Ty
p
e
(1)
I/
O
L
e
vel
(2
)
Main
function(3)
(after reset)
Alternate functions
BGA
100
LQ
FP48
LQ
FP64
LQ
FP100
VFQFP
N
36
Default
Remap
相關PDF資料
PDF描述
STM32W108CBU62 SPECIALTY MICROPROCESSOR CIRCUIT, QCC48
STM8L162R8T3 8-BIT, FLASH, 16 MHz, RISC MICROCONTROLLER, PQFP64
STM8L162R8T6 8-BIT, FLASH, 16 MHz, RISC MICROCONTROLLER, PQFP64
STMPE2401TBR 24 I/O, PIA-GENERAL PURPOSE, PBGA36
STMPE801MTR 8 I/O, PIA-GENERAL PURPOSE, PDSO16
相關代理商/技術參數
參數描述
STM32F103T6U6AXXX 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Low-density performance line, ARM-based 32-bit MCU with 16 or 32 KB Flash, USB, CAN, 6 timers, 2 ADCs, 6 communication interfaces
STM32F103T6U6TR 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Low-density performance line, ARM-based 32-bit MCU with 16 or 32 KB Flash, USB, CAN, 6 timers, 2 ADCs, 6 communication interfaces
STM32F103T6U6XXX 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Low-density performance line, ARM-based 32-bit MCU with 16 or 32 KB Flash, USB, CAN, 6 timers, 2 ADCs, 6 communication interfaces
STM32F103T6U7A 功能描述:ARM微控制器 - MCU 32BIT Cortex M3 L/D Performance LINE RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT
STM32F103T6U7ATR 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Low-density performance line, ARM-based 32-bit MCU with 16 or 32 KB Flash, USB, CAN, 6 timers, 2 ADCs, 6 communication interfaces