- 您現在的位置：買賣IC網 > PDF目錄380763 > STDS75 (意法半導體) Digital temperature sensor and thermal watchdog PDF資料下載
參數資料
| 型號： | STDS75 |
| 廠商： | 意法半導體 |
| 元件分類： | 溫度/濕度傳感器 |
| 英文描述： | Digital temperature sensor and thermal watchdog |
| 中文描述： | 數字溫度傳感器和熱看門狗 |
| 文件頁數： | 20/37頁 |
| 文件大?。?/td> | 204K |
| 代理商： | STDS75 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁
Functional description
STDS75
20/37
3.3
Serial interface
Writing to and reading from the STDS75 registers is accomplished via the two-wire serial
interface protocol which requires that one device on the bus initiates and controls all READ
and WRITE operations. This device is called the “master” device. The master device also
generates the SCL signal which provides the clock signal for all other devices on the bus.
These other devices on the bus are called “slave” devices. The STDS75 is a slave device
(see
Table 10
). Both the master and slave devices can send and receive data on the bus.
During operations, one data bit is transmitted per clock cycle. All operations follow a
repeating, nine-clock-cycle pattern that consists of eight bits (one byte) of transmitted data
followed by an acknowledge (ACK) or not acknowledge (NACK) from the receiving device.
Note:
There are no unused clock cycles during any operation, so there must not be any breaks in
the data stream and ACKs/NACKs during data transfers. Conversely, having too few clock
cycles can lead to incorrect operation if an inadvertent 8-bit READ from a 16-bit register
occurs.
Table 10.
3.4
2-wire bus characteristics
The bus is intended for communication between different ICs. It consists of two lines: a bi-
directional data signal (SDA) and a clock signal (SCL). Both the SDA and SCL lines must be
connected to a positive supply voltage via a pull-up resistor.
The following protocol has been defined:
Data transfer may be initiated only when the bus is not busy.
During data transfer, the data line must remain stable whenever the clock line is High.
Changes in the data line, while the clock line is High, will be interpreted as control
signals.
●
●
●
●
Accordingly, the following bus conditions have been defined (see
Figure 6 on page 21
):
3.4.1
Bus not busy
Both data and clock lines remain High.
3.4.2
Start data transfer
A change in the state of the data line, from high to Low, while the clock is High, defines the
START condition.
3.4.3
Stop data transfer
A change in the state of the data line, from Low to High, while the clock is High, defines the
STOP condition.
STDS75 serial bus slave addresses
MSB
LSB
Bit7
Bit6
Bit5
Bit4
Bit3
Bit2
Bit1
Bit0
1
0
0
1
A2
A1
A0
R/W
相關PDF資料 |
PDF描述 |
|---|---|
| STDS75DS2E | Digital temperature sensor and thermal watchdog |
| STDS75DS2F | Digital temperature sensor and thermal watchdog |
| STDS75M2E | Digital temperature sensor and thermal watchdog |
| STDS75M2F | Digital temperature sensor and thermal watchdog |
| STE2001DIE1 | 65 X 128 SINGLE CHIP LCD CONTROLLER / DRIVER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| STDS75_08 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Digital temperature sensor and thermal watchdog |
| STDS75DS2E | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Digital temperature sensor and thermal watchdog |
| STDS75DS2F | 功能描述:板上安裝溫度傳感器 Digital TEMP sensor thermal watchdog RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| STDS75M2E | 功能描述:板上安裝溫度傳感器 Digital Temp Snsr Thermal Watchdog RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| STDS75M2F | 功能描述:板上安裝溫度傳感器 Digital Temp Snsr Thermal Watchdog RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發(fā)布緊急采購，3分鐘左右您將得到回復。