- 您現在的位置：買賣IC網 > PDF目錄380762 > STCF03PNR (意法半導體) High power white LED driver with I2C⑩ interface PDF資料下載
參數資料
| 型號： | STCF03PNR |
| 廠商： | 意法半導體 |
| 元件分類： | LED驅動器 |
| 英文描述： | High power white LED driver with I2C⑩ interface |
| 中文描述： | 大功率白光LED驅動器具有I2C⑩接口 |
| 文件頁數： | 20/35頁 |
| 文件大?。?/td> | 455K |
| 代理商： | STCF03PNR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁
Description of internal registers
STCF03
20/35
8
Description of internal registers
8.1
PWR_ON
When set, it activates all analog and power internal blocks including the NTC supporting
circuit, and the device is ready to operate (Ready Mode). As long as PWR_ON=0, only the
I
2
C interface is active, minimizing Stand-by Mode power consumption.
8.2
TRIG_EN
This bit is AND-ed with the TRIG pin to generate the internal signal FL_ON that activates
Flash Mode. By this way, both soft-triggering and hard-triggering of the Flash are made
possible. If soft-triggering (through I
2
C) is chosen, the TRIG pin is not used and must be
kept HIGH (VI). If hard-triggering is chosen, then the TRIG pin has to be connected to a μP
I/O devoted to Flash timing control, and the TRIG_EN bit must be set in advance. Both
triggering modes can benefit of the internal Flash Time Counter, that uses the TRIG_EN bit
and can work either as a safety shut-down timer or as a Flash duration timer. Flash mode
can start only if PWR_ON=1. LED current is controlled by the value set by the FDIM_0~3 of
the DIM_REG.
8.3
TCH_ON
When set from Ready Mode, the STCF03 enters the Torch mode. The LED current is
controlled by the value set by the TDIM_0~3 of the DIM_REG.
8.4
NTC_ON
In ready mode, the comparators that monitor the LED temperature are activated if NTC_ON
bit is set. NTC-related blocks are always active regardless of this bit in Torch mode and
Flash mode.
Table 9. I
2
C Register mapping function
Register name
SUB ADDRESS (hex)
Operation
CMD_REG
00
R / W
DIM_REG
01
R / W
AUX_REG
02
R / W
STAT_REG
03
R only
Table 10. Command register
CMD_REG
(write mode)
MSB
LSB
SUB ADD=00
PWR_ON
TRIG_EN
TCH_ON
NTC_ON
FTIM_3
FTIM_2
FTIM_1
FTIM_0
Power ON
RESET Value
0
0
0
0
0
0
0
0
相關PDF資料 |
PDF描述 |
|---|---|
| STCF03TBR | High power white LED driver with I2C⑩ interface |
| STCN75 | Digital temperature sensor and thermal watchdog |
| STCN75DS2E | Digital temperature sensor and thermal watchdog |
| STCN75DS2F | Digital temperature sensor and thermal watchdog |
| STCN75M2E | Digital temperature sensor and thermal watchdog |
相關代理商/技術參數 |
參數描述 |
|---|---|
| STCF03TBR | 功能描述:LED照明驅動器 HP white LED driver RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| STCF04 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:High power white LED SuperCap driver with I²C interface |
| STCF04TBR | 功能描述:LED照明驅動器 HP WH LED SuperCap Driver I2C 1.5A 5.5V RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| STCF06 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:1.5 A white LED driver with IC interface |
| STCF06TBR | 功能描述:LED照明驅動器 1.5A WHITE LED DRVR RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
發布緊急采購，3分鐘左右您將得到回復。