- 您現在的位置：買賣IC網 > PDF目錄380759 > STA575 (意法半導體) DISCONNECT SWITCH+HANDLE 600VAC 30A IEC PDF資料下載
參數資料
| 型號： | STA575 |
| 廠商： | 意法半導體 |
| 元件分類： | 音頻放大器 |
| 英文描述： | DISCONNECT SWITCH+HANDLE 600VAC 30A IEC |
| 中文描述： | 100 100W的立體聲BASH功放 |
| 文件頁數： | 15/20頁 |
| 文件大?。?/td> | 278K |
| 代理商： | STA575 |
15/20
STA575
Interfacing STA575 to STPB01 (Feedback circuit)
This circuit produces a control signal current that is fed back to the STPB01 digital controller. The network used
in this example compares the track signal (STA575 track out) to a fixed ratio of buck regulator's output (CD+)
using a transistor. This method is effective because the controller's reference is the negative of the main DC
supply, which is not referenced to audio ground.
The tracking signal is generated inside the STA575 (track out) by taking the absolute value of the pre-amp's
output. The outputs of each channel and of each STA575 are then tied together in a diode-oring arrangement.
This means that the highest of any given output is the output that determines the tracking signal.
The absolute value circuit inside the STA575 has gain. This makes it possible to use an RC network and a re-
sistor divider to create a phase shift in the tracking signal at higher frequencies. This is also useful in optimizing
the alignment of the buck regulator's output with the output signal of the bridge amplifier at high frequency
This circuit first converts the buck switch current to a peak voltage. The control current is then converted to a
voltage (using a resistor) and added to the peak voltage. By doing this, the buck is better able to maintain the
desired headroom over a wide load range and output level.
Centering Network for CD+ & CD- Rails
The power rail of a bridge amplifier has no current flowing through the ground node, as the load is not connected
to ground. However there are several different small sources of dynamic and continuos ground currents flowing
from either CD+ or CD- to support the function of various things such as the control signal to the STABP01 con-
troller.
The centering network prevents these currents from shifting the CD+/- rails away from center i.e. away from a
symmetric split of the buck's output about ground. This is critical, even a small centering error requires an in-
crease in headroom which results in a significant drop in output losses. In its simplest form the centering network
could be a resistor divider from CD+ to CD- with its center tied to ground.
As long as the impedance is low enough (for example 200 ohms) this will swamp the smaller offset currents. It
is helpful to put this kind of passive network on the board with the STA575 devices to help when testing this
board on its own.
Power Amplifier Heatsink requirements
The heatsink requirements are dependent on several design goals. However there are two common references:
Pink noise at 1/8 of full power, all channels loaded. This would approximate a system with all channels repro-
ducing music at full volume with clipping occurring only occasionally. The second would be full power at 1kHz
for 5 minutes after a one hour pre-soak at 1/8 power.
The worse of these two is the full power test. A conservative approach is to assume that the heatsink would
come to thermal equilibrium after 5 minutes. Thus the Rth of the heatsink can be determined by:
For example in the STA575 the Rth jc is 1°C / W. R case-to-heatsink with grease is about 0.5°C / W. The max-
imum operating junction temperature is 130°C, which for margin should be derated to 120°C
Buck Regulator Heatsink
The Buck regulator heatsink can be designed in a similar manner and does not change by varying power supply.
In general the efficiency will be in the order of 85%. The thermal impedances from the junction(s) to the heatsink
may be lower and the maximum operating temperature will be higher.
Usually either the sub or the remaining channels are tested at full power. The result is that usually the Buck
heatsink is about the size of the linear heatsink, but this can be strongly affected by the design.
R
th heatsink
T
----------------------------------
T
–
d
R
th j case
–
R
th case to heatsink
–
–
=
相關PDF資料 |
PDF描述 |
|---|---|
| STA7056 | 3W MONO BRIDGE AMPLIFIER |
| STA7360 | 20W BRIDGE/STEREO AUDIO AMPLIFIER WITH CLIPPING DETECTOR |
| STAN250A | RF & MICROWAVE TRANSISTORS AVIONICS APPLICATIONS |
| START405 | NPN Silicon RF Transistor |
| START405TR | NPN Silicon RF Transistor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| STA-5760 | 功能描述:插入式交流適配器 2.1x5.5mm Neg PLUG RoHS:否 制造商:Phihong 地區:Universal 安裝風格:Wall, Interchangeable Plug 輸入電壓范圍:90 VAC to 264 VAC 輸出端數量:1 輸出功率額定值:5 W 輸出電壓（通道 1）:5 V 輸出電流（通道 1）:1 A 直流輸出連接器:USB Type A 隨附/必需的交流插頭:Required 商用/醫用:Commercial 效率:Level V |
| STA-5760A | 功能描述:插入式交流適配器 120Vac 6Vac 3300mA AC-AC Desktop RoHS:否 制造商:Phihong 地區:Universal 安裝風格:Wall, Interchangeable Plug 輸入電壓范圍:90 VAC to 264 VAC 輸出端數量:1 輸出功率額定值:5 W 輸出電壓（通道 1）:5 V 輸出電流（通道 1）:1 A 直流輸出連接器:USB Type A 隨附/必需的交流插頭:Required 商用/醫用:Commercial 效率:Level V |
| STA-5775 | 制造商:Stancor 功能描述:Plug-In Adapter Single-OUT 7.5V 1.5A |
| STA-5790 | 功能描述:插入式交流適配器 9VAC 3400mA DESK-TOP RoHS:否 制造商:Phihong 地區:Universal 安裝風格:Wall, Interchangeable Plug 輸入電壓范圍:90 VAC to 264 VAC 輸出端數量:1 輸出功率額定值:5 W 輸出電壓（通道 1）:5 V 輸出電流（通道 1）:1 A 直流輸出連接器:USB Type A 隨附/必需的交流插頭:Required 商用/醫用:Commercial 效率:Level V |
| STA-6033 | 制造商:RF Micro Devices Inc 功能描述:IC AMP HBT 5.9GHZ 3.3V 16-QFN |
發布緊急采購，3分鐘左右您將得到回復。