- 您現在的位置：買賣IC網 > PDF目錄380758 > ST93C57CM1TR (意法半導體) 2K 128 x 16 or 256 x 8 SERIAL MICROWIRE EEPROM PDF資料下載
參數資料
| 型號： | ST93C57CM1TR |
| 廠商： | 意法半導體 |
| 英文描述： | 2K 128 x 16 or 256 x 8 SERIAL MICROWIRE EEPROM |
| 中文描述： | 2K 128 x 16或256 × 8 MICROWIRE的串行EEPROM的 |
| 文件頁數： | 6/13頁 |
| 文件大小： | 108K |
| 代理商： | ST93C57CM1TR |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁
Instruction
Description
Op-Code
x8 Org
Address
(ORG = 0)
(1, 2)
Data
x16 Org
Address
(ORG = 1)
(1, 3)
Data
READ
Read Data from Memory
10
A8-A0
Q7-Q0
A7-A0
Q15-Q0
WRITE
Write Data to Memory
01
A8-A0
D7-D0
A7-A0
D15-D0
EWEN
Erase/Write Enable
00
11XXX XXXX
11XX XXXX
EWDS
Erase/Write Disable
00
00XXX XXXX
00XX XXXX
ERASE
Erase Byteor Word
11
A8-A0
A7-A0
ERAL
Erase AllMemory
00
10XXX XXXX
10XX XXXX
WRAL
Write All Memory
with same Data
00
01XXX XXXX
D7-D0
01XX XXXX
D15-D0
Notes:
1. X =don’t care bit.
2. Address bit A8 is not decoded by theST93C56, ST93C56C.
3. Address bit A7 is not decoded by theST93C56, ST93C56C.
Table 6. InstructionSet
INSTRUCTIONS
The ST93C56 has seven instructions, asshownin
Table 6.The op-codesofthe instructionsaremade
up of2 bits.The op-code isfollowed byan address
for thebyte/wordwhich is eightbitslongforthe x16
organization or nine bits long for the x8 organiza-
tion.Eachinstructionisprecededbythe rising edge
of the signal applied on the Chip Select (S) input
(assuming that the clock C is low). The data input
D is thensampled upon the followingrising edges
of the clock C untill a ’1’ is sampled and decoded
by the ST93C56as a Start bit.
The ST93C56 is fabricated in CMOS technology
and is therefore able to run from zero Hz (static
inputsignals)upto themaximumratings(specified
in Table5).
Read
The Read instruction (READ) outputs serial data
on the Data Output (Q). When a READ instruction
is received, the instruction and address are de-
codedandthe datafrom thememory istransferred
intoanoutputshiftregister.Adummy’0’bitisoutput
first, followed by the 8 bit byte or the 16 bit word
with the MSB first. Output data changes are trig-
geredby theLowtoHightransitionoftheClock(C).
The ST93C56will automaticallyincrement the ad-
dressand will clock out the next byte/wordas long
as the Chip Select input (S) is held High. In this
case the dummy ’0’ bit is NOT output between
bytes/words and a continuousstream of data can
be read.
Erase/WriteEnable and Disable
The Erase/Write Enable instruction (EWEN)
authorizesthe followingErase/Writeinstructionsto
be executed, the Erase/Write Disable instruction
(EWDS) disables the execution of the following
Erase/Write instructions. When power is first ap-
plied, the ST93C56 enters the Disable mode.
When the EWEN instruction is executed, Write
instructions remain enabled until an Erase/Write
Disableinstruction(EWDS) isexecutedorV
CC
falls
below the power-onreset threshold.To protectthe
memory contents from accidental corruption, it is
advisabletoissuetheEWDSinstruction afterevery
write cycle.
The READ instructionis notaffectedbythe EWEN
or EWDSinstructions.
Erase
The Erase instruction (ERASE) programs the ad-
dressedmemory byte or word bits to ’1’. Once the
addressiscorrectlydecoded,the fallingedgeof the
Chip Select input (S) triggers a self-timed erase
cycle.
If the ST93C56 is still performing the erasecycle,
the Busysignal(Q=0) will bereturnedif Sisdriven
high, and the ST93C56will ignore any data on the
bus. Whentheerasecycle iscompleted,theReady
signal (Q = 1) will indicate (if S is driven high) that
the ST93C56is ready to receive a new instruction.
Write
The Write instruction (WRITE) is followed by the
addressandthe8or16databitsto bewritten. Data
input is sampled on the Low to High transition of
the clock.After thelast databit has beensampled,
Chip Select (S) must be brought Low before the
next rising edge of the clock (C) in order to start
the self-timed programming cycle. If the ST93C56
is still performing the write cycle, the Busy signal
6/13
ST93C56/56C, ST93C57C
相關PDF資料 |
PDF描述 |
|---|---|
| ST93C57CM3013TR | 2K 128 x 16 or 256 x 8 SERIAL MICROWIRE EEPROM |
| ST93C57CM3TR | 2K 128 x 16 or 256 x 8 SERIAL MICROWIRE EEPROM |
| ST93C57CM6013TR | 2K 128 x 16 or 256 x 8 SERIAL MICROWIRE EEPROM |
| ST93C57CM6TR | 2K 128 x 16 or 256 x 8 SERIAL MICROWIRE EEPROM |
| ST93C56CM3TR | MODULAR PLUG, UNSHLD, ROUND CABLE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST93C57CM3 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microwire Serial EEPROM |
| ST93C57CM3013TR | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:2K 128 x 16 or 256 x 8 SERIAL MICROWIRE EEPROM |
| ST93C57CM3TR | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:2K 128 x 16 or 256 x 8 SERIAL MICROWIRE EEPROM |
| ST93C57CM6 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microwire Serial EEPROM |
| ST93C57CM6013TR | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:2K 128 x 16 or 256 x 8 SERIAL MICROWIRE EEPROM |
發布緊急采購，3分鐘左右您將得到回復。