REV. 5.1.0 ECP/EPP PARALLEL PRINTER PORT WITH 16-BYTE FIFO 4.0 DEVICE OPERATION 4.1 SPP MODE This is ECR mode 000 " />
參數資料
型號： ST78C36CJ44-F
廠商： Exar Corporation
文件頁數： 3/27頁
文件大?。?/td> 0K
描述： IC UART FIFO 16B 44PLCC
標準包裝： 27
特點： *
FIFO's： 16 字節
規程： 打印機
電源電壓： 5V
帶并行端口： 是
安裝類型： 表面貼裝
封裝/外殼： 44-LCC（J 形引線）
供應商設備封裝： 44-PLCC（16.59x16.59）
包裝： 管件
ST78C36/36A
11
REV. 5.1.0
ECP/EPP PARALLEL PRINTER PORT WITH 16-BYTE FIFO
4.0 DEVICE OPERATION
4.1
SPP MODE
This is ECR mode 000 (system RESET mode).
In this output-only mode the host data is registered to PD[7:0] at the trailing edge of -IOW; PDIR is driven low;
-STROBE, -AUTOFD, INIT, and -SLCTIN are open-drain; and all timing is managed by the host through DSR
and DCR registers.
4.2
PS2 MODE
This is ECR mode 001.
In this bi-directional mode the host output data is registered to PD[7:0] at the trailing edge of -IOW, PDIR is
driven by DIR to allow peripheral data input, -AUTOFD, INIT, and -SLCTIN are totem-pole, and all timing is
managed by the host through DSR and DCR registers.
4.3
PPF MODE
This is ECR mode 010.
In this output-only mode the host data is written to the FIFO with I/O writes to address 400 or by DMA writes;
PDIR is driven low; -AUTOFD, INIT, and -SLCTIN are totem-pole.
FIFO data is automatically registered to PD[7:0] whenever the FIFO-E bit is low (data available), and timing is
generated by controller logic that handshakes -STROBE (controller) with BUSY (peripheral).
4.4
ECP MODE
This is ECR mode 011.
In this bi-directional mode the host data is written to the FIFO with I/O writes to address 000, 400 or DMA;
PDIR is driven by DIR (can only be set in ECR mode 001); -AUTOFD, INIT, and -SLCTIN are totem-pole. I/O
writes to address 000 will write a low into the FIFO tag bit, while I/O writes to address 400 or DMA will insert a
high.
4.4.1
ECP FORWARD MODE (PDIR = 0)
FIFO data is automatically registered to PD[7:0] whenever the FIFO-E bit is low (data available), and timing is
generated by controller logic that handshakes -STROBE (controller) with BUSY (peripheral). Data from the
FIFO tag bit is output on -AUTOFD after being registered simultaneous with FIFO data.
相關PDF資料
PDF描述
ST16C580CQ48-F IC UART FIFO 16B 48TQFP
XR88C92CVTR-F IC UART FIFO DUAL 44LQFP
XR88C92CJTR-F IC UART FIFO DUAL 44PLCC
ST16C452CJ68TR-F IC UART W/PAR PORT DUAL 68PLCC
ST16C552CJ68TR-F IC UART FIFO 16B DUAL 68PLCC
相關代理商/技術參數
參數描述
ST78C36CJ44TR-F 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
ST78C36CQ-0A-EVB 功能描述:界面開發工具 Supports 78C36 64 ld TQFP, ISA Interface RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
ST78C36CQ64 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述:
ST78C36CQ64-F 功能描述:接口 - 專用 UART RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
ST78L05 制造商:SEMTECH_ELEC 制造商全稱:SEMTECH ELECTRONICS LTD. 功能描述:3-Terminal positive voltage regulator
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*