- 您現在的位置：買賣IC網 > PDF目錄381094 > ST24C08B5TR (意法半導體) 8 Kbit Serial I2C Bus EEPROM with User-Defined Block Write Protection PDF資料下載
參數資料
| 型號： | ST24C08B5TR |
| 廠商： | 意法半導體 |
| 元件分類： | DRAM |
| 英文描述： | 8 Kbit Serial I2C Bus EEPROM with User-Defined Block Write Protection |
| 中文描述： | 8千位串行I2C總線的EEPROM與用戶定義的塊寫保護 |
| 文件頁數： | 11/16頁 |
| 文件大?。?/td> | 125K |
| 代理商： | ST24C08B5TR |
S
S
BYTE WRITE
DEV SEL
BYTE ADDR
DATA IN
WC
S
PAGE WRITE
DEV SEL
BYTE ADDR
DATA IN 1
WC
DATA IN 2
AI01161B
PAGE WRITE
(cont'd)
WC (cont'd)
S
DATA IN N
ACK
ACK
NO ACK
R/W
ACK
ACK
NO ACK
R/W
NO ACK
NO ACK
Figure 10. Write Modes Sequence with Write Control = 1 (ST24/25W08)
Read Operations
Read operations are independent of the state of the
MODE pin. On delivery, the memory content is set
at all "1’s" (or FFh).
Current Address Read.
The memory has an inter-
nal byte address counter. Each time a byte is read,
this counter is incremented. For the Current Ad-
dress Read mode, following a START condition,
the master sends a memory address with the RW
bit set to ’1’. The memory acknowledges this and
outputs the byte addressed by the internal byte
address counter. This counter is then incremented.
The master does NOT acknowledge the byte out-
put, but terminates the transfer with a STOP con-
dition.
Random Address Read.
A dummy write is per-
formed to load the address into the address counter
(see Figure 11). This is followed by another START
condition from the master and the byte address is
repeated with the RW bit set to ’1’. The memory
acknowledges this and outputs the byte ad-
dressed. The master have to NOT acknowledge
the byte output, but terminates the transfer with a
STOP condition.
Sequential Read.
This mode can be initiated with
either a Current Address Read or a Random Ad-
dress Read. However, in this case the master
DOES acknowledge the data byte output and the
memory continues to output the next byte in se-
quence. To terminate the stream of bytes, the
11/16
ST24/25C08, ST24/25W08
相關PDF資料 |
PDF描述 |
|---|---|
| ST25C08B1TR | 8 Kbit Serial I2C Bus EEPROM with User-Defined Block Write Protection |
| ST25C08B3TR | 8 Kbit Serial I2C Bus EEPROM with User-Defined Block Write Protection |
| ST25C08B5TR | 8 Kbit Serial I2C Bus EEPROM with User-Defined Block Write Protection |
| ST25C08M1TR | 8 Kbit Serial I2C Bus EEPROM with User-Defined Block Write Protection |
| ST25C08M3TR | 8 Kbit Serial I2C Bus EEPROM with User-Defined Block Write Protection |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST24C08B6 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:I2C Serial EEPROM |
| ST24C08B6TR | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8 Kbit Serial I2C Bus EEPROM with User-Defined Block Write Protection |
| ST24C08CM1 | 功能描述:電可擦除可編程只讀存儲器 RO 511-M24C08-MN6 SO-8 8K SER 電可擦除可編程只讀存儲器 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| ST24C08M1 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:I2C Serial EEPROM |
| ST24C08M1TR | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8 Kbit Serial I2C Bus EEPROM with User-Defined Block Write Protection |
發布緊急采購，3分鐘左右您將得到回復。