- 您現在的位置：買賣IC網 > PDF目錄3763 > ST16C552ACJ68-F (Exar Corporation)IC UART FIFO 16B DUAL 68PLCC PDF資料下載
參數資料
| 型號： | ST16C552ACJ68-F |
| 廠商： | Exar Corporation |
| 文件頁數： | 34/39頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC UART FIFO 16B DUAL 68PLCC |
| 標準包裝： | 19 |
| 特點： | * |
| 通道數： | 2，DUART |
| FIFO's： | 16 字節 |
| 規程： | 打印機 |
| 電源電壓： | 2.97 V ~ 5.5 V |
| 帶并行端口： | 是 |
| 帶故障啟動位檢測功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 帶CMOS： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 68-LCC（J 形引線） |
| 供應商設備封裝： | 68-PLCC |
| 包裝： | 管件 |
| 其它名稱： | 1016-1666 ST16C552ACJ68-F-ND |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁當前第34頁第35頁第36頁第37頁第38頁第39頁
4
ST16C552/552A
Rev. 3.40
SYMBOL DESCRIPTION
Symbol
Pin
Signal Type
Pin Description
-ERROR
63
I
Error, Printer (with internal pull-up) - General purpose input
or line printer error. This pin may be connected to the active
low (logic 0) output of a printer to indicate an error condition.
GND
2,7,54
Pwr
Signal and Power Ground.
27
INIT
57
I/O
Initialize (open drain, with internal pull-up) - General pur-
pose I/O signal. This pin may be connected for initialization
service of a connected line printer. Generally when this
signal is a logic 0, any connected printer will be initialized.
INT A/B
45,60
O
Interrupt output A/B ( three state active high) - These pins
provide individual channel interrupts, INT A-B. INT A-B are
enabled when MCR bit-3 is set to a logic 1, interrupts are
enabled in the interrupt enable register (IER), and when an
interrupt condition exists. Interrupt conditions include: re-
ceiver errors, available receiver buffer data, transmit buffer
empty, or when a modem status flag is detected.
-INTP
59
O
Printer Interrupt,
- This pin can be used to signal the
interrupt status of a connected printer. This pin basically
tracks the -ACK input pin, When INTSEL is a logic 0 and
interrupts are enabled by bit-4 in the control register. A
latched mode can be selected by setting INTSEL to a logic
1. In this case the interrupt -INTP is generated normally but
does not return to the inactive state until the trailing edge of
the read cycle (-IOR pin). -INTP is three stated until CON
bit-4 is set to a logic 1. The difference between the
ST16C552 and ST16C552A is the output state of INTP.
INTP is active high (logic 1) on the ST16C552 whereas
INTP is active low (logic 0) on the ST16C552A part when the
interrupt latch mode is selected.
INTSEL
43
I
Interrupt Select mode - This pin selects the interrupt type for
the printer port (-INTP). When this pin is a logic 0, the
external -ACK signal state is generally followed, minus
some minor propagation delay. Making this pin a logic 1 or
connecting it to VCC will set the interrupt latched mode. In this
case the printer interrupt (-INTP) will not return to a logic 0 on
the 552 or a logic 1 on the 552A (552A is inverted), until the
相關PDF資料 |
PDF描述 |
|---|---|
| ST16C650ACJ44-F | IC UART FIFO 32B 44PLCC |
| XR20M1170IG24-F | IC UART FIFO I2C/SPI 64B 24TSSOP |
| XR20M1170IG16-F | IC UART FIFO I2C/SPI 64B 16TSSOP |
| MAX3110EEWI+G36 | IC UART SPI COMPAT 28-SOIC |
| MAX3111EEWI+G36 | IC TXRX RS232 SPI W/CAP 28-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST16C552ACJ68TR-F | 功能描述:UART 接口集成電路 DUAL UART W/16BYTE FIFO&PARALELPRNTPORT RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| ST16C552AIJ68 | 制造商:EXAR 制造商全稱:EXAR 功能描述:DUAL UART WITH 16-BYTE FIFO AND PARALLEL PRINTER PORT |
| ST16C552AIJ68-F | 功能描述:UART 接口集成電路 DUAL UART W/16BYTE FIFO&PARALELPRNTPORT RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| ST16C552CJ | 制造商:STARTECH 功能描述: |
| ST16C552CJ68 | 制造商:Rochester Electronics LLC 功能描述:DUAL PORT 16 BYTE FIFO AND PARALLEL PRINTR - Bulk 制造商:Exar Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。