- 您現在的位置：買賣IC網 > PDF目錄3762 > ST16C2552CJ44TR-F (Exar Corporation)IC UART FIFO 16B DUAL 44PLCC PDF資料下載
參數資料
| 型號： | ST16C2552CJ44TR-F |
| 廠商： | Exar Corporation |
| 文件頁數： | 9/34頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC UART FIFO 16B DUAL 44PLCC |
| 標準包裝： | 500 |
| 特點： | * |
| 通道數： | 2，DUART |
| FIFO's： | 16 字節 |
| 規程： | RS232，RS485 |
| 電源電壓： | 3.3 V ~ 5 V |
| 帶故障啟動位檢測功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 帶CMOS： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 44-LCC（J 形引線） |
| 供應商設備封裝： | 44-PLCC（16.59x16.59） |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁
ST16C2552
17
REV. 4.2.2
2.97V TO 5.5V DUAL UART WITH 16-BYTE FIFO
4.3
Baud Rate Generator Divisors (DLL and DLM) - Read/Write
The Baud Rate Generator (BRG) is a 16-bit counter that generates the data rate for the transmitter. The rate is
programmed through registers DLL and DLM which are only accessible when LCR bit-7 is set to ‘1’.
SEE”PROGRAMMABLE BAUD RATE GENERATOR” ON PAGE 10. for more details.
4.4
Interrupt Enable Register (IER) - Read/Write
The Interrupt Enable Register (IER) masks the interrupts from receive data ready, transmit empty, line status
and modem status registers. These interrupts are reported in the Interrupt Status Register (ISR).
4.4.1
IER versus Receive FIFO Interrupt Mode Operation
When the receive FIFO (FCR BIT-0 = 1) and receive interrupts (IER BIT-0 = 1) are enabled, the RHR interrupts
(see ISR bits 2 and 3) status will reflect the following:
A. The receive data available interrupts are issued to the host when the FIFO has reached the programmed
trigger level. It will be cleared when the FIFO drops below the programmed trigger level.
B. FIFO level will be reflected in the ISR register when the FIFO trigger level is reached. Both the ISR register
status bit and the interrupt will be cleared when the FIFO drops below the trigger level.
C. The receive data ready bit (LSR BIT-0) is set as soon as a character is transferred from the shift register to
the receive FIFO. It is reset when the FIFO is empty.
4.4.2
IER versus Receive/Transmit FIFO Polled Mode Operation
When FCR BIT-0 equals a logic 1 for FIFO enable; resetting IER bits 0-3 enables the ST16C2552 in the FIFO
polled mode of operation. Since the receiver and transmitter have separate bits in the LSR either or both can
be used in the polled mode by selecting respective transmit or receive control bit(s).
A. LSR BIT-0 indicates there is data in RHR or RX FIFO.
B. LSR BIT-1 indicates an overrun error has occurred and that data in the FIFO may not be valid.
C. LSR BIT 2-4 provides the type of receive data errors encountered for the data byte in RHR, if any.
D. LSR BIT-5 indicates transmit FIFO is empty.
E. LSR BIT-6 indicates when both the transmit FIFO and TSR are empty.
F. LSR BIT-7 indicates a data error in at least one character in the RX FIFO.
IER[0]: RHR Interrupt Enable
The receive data ready interrupt will be issued when RHR has a data character in the non-FIFO mode or when
the receive FIFO has reached the programmed trigger level in the FIFO mode.
Logic 0 = Disable the receive data ready interrupt (default).
Logic 1 = Enable the receiver data ready interrupt.
IER[1]: THR Interrupt Enable
This bit enables the Transmit Ready interrupt which is issued whenever the TX FIFO becomes empty.
Logic 0 = Disable Transmit Ready interrupt (default).
Logic 1 = Enable Transmit Ready interrupt.
IER[2]: Receive Line Status Interrupt Enable
If any of the LSR register bits 1, 2, 3 or 4 is a logic 1, it will generate an interrupt to inform the host controller
about the error status of the current data byte in FIFO. LSR bit-1 generates an interrupt immediately when the
character has been received. LSR bits 2-4 generate an interrupt when the character with errors is read out of
the FIFO.
Logic 0 = Disable the receiver line status interrupt (default).
Logic 1 = Enable the receiver line status interrupt.
相關PDF資料 |
PDF描述 |
|---|---|
| ST78C36CJ44-F | IC UART FIFO 16B 44PLCC |
| ST16C580CQ48-F | IC UART FIFO 16B 48TQFP |
| XR88C92CVTR-F | IC UART FIFO DUAL 44LQFP |
| XR88C92CJTR-F | IC UART FIFO DUAL 44PLCC |
| ST16C452CJ68TR-F | IC UART W/PAR PORT DUAL 68PLCC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST16C2552CQ48 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:UART |
| ST16C2552IJ | 制造商:Exar Corporation 功能描述:2 CHANNEL(S), 4M bps, SERIAL COMM CONTROLLER, PQCC44 |
| ST16C2552IJ44 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述: 制造商:Exar Corporation 功能描述:UART, 44 Pin, Plastic, PLCC |
| ST16C2552IJ44-F | 功能描述:UART 接口集成電路 2.97V-5.5V 16B FIFO temp -45 to 85C;UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| ST16C2552IJ44TR-F | 功能描述:UART 接口集成電路 DUAL UART W/16BYTE FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。