REV. 4.4.1 2.97V TO 5.5V DUART WITH 16-BYTE FIFO MCR[3]: OP2# Output / INT Output Enable This bit enables and disables the operati" />
參數資料
型號： ST16C2550CQ48TR-F
廠商： Exar Corporation
文件頁數： 16/37頁
文件大?。?/td> 0K
描述： IC UART FIFO 16B DUAL 48TQFP
標準包裝： 1,500
特點： *
通道數： 2，DUART
FIFO's： 16 字節
規程： RS232，RS485
電源電壓： 2.97 V ~ 5.5 V
帶故障啟動位檢測功能： 是
帶調制解調器控制功能： 是
帶CMOS： 是
安裝類型： 表面貼裝
封裝/外殼： 48-TQFP
供應商設備封裝： 48-TQFP（7x7）
包裝： 帶卷 (TR)
ST16C2550
23
REV. 4.4.1
2.97V TO 5.5V DUART WITH 16-BYTE FIFO
MCR[3]: OP2# Output / INT Output Enable
This bit enables and disables the operation of INT, interrupt output. If INT output is not used, OP2# can be
used as a general purpose output.
Logic 0 = INT (A-B) outputs disabled (three state mode) and OP2# output set to a logic 1 (default).
Logic 1 = INT (A-B) outputs enabled (active mode) and OP2# output set to a logic 0.
MCR[4]: Internal Loopback Enable
Logic 0 = Disable loopback mode (default).
Logic 1 = Enable local loopback mode, see loopback section and Figure 11.
MCR[7:5]: Reserved
4.8
Line Status Register (LSR) - Read Only
This register provides the status of data transfers between the UART and the host.
LSR[0]: Receive Data Ready Indicator
Logic 0 = No data in receive holding register or FIFO (default).
Logic 1 = Data has been received and is saved in the receive holding register or FIFO.
LSR[1]: Receiver Overrun Flag
Logic 0 = No overrun error (default).
Logic 1 = Overrun error. A data overrun error condition occurred in the receive shift register. This happens
when additional data arrives while the FIFO is full. In this case the previous data in the receive shift register
is overwritten. Note that under this condition the data byte in the receive shift register is not transferred into
the FIFO, therefore the data in the FIFO is not corrupted by the error. An interrupt will be generated
immediately if LSR interrupt is enabled (IER bit-2).
LSR[2]: Receive Data Parity Error Flag
Logic 0 = No parity error (default).
Logic 1 = Parity error. The receive character in RHR does not have correct parity information and is suspect.
This error is associated with the character available for reading in RHR. If the LSR interrupt is enabled (IER
bit-2), an interrupt will be generated when the character is in the RHR.
LSR[3]: Receive Data Framing Error Flag
Logic 0 = No framing error (default).
Logic 1 = Framing error. The receive character did not have a valid stop bit(s). This error is associated with
the character available for reading in RHR. If the LSR interrupt is enabled (IER bit-2), an interrupt will be
generated when the character is in the RHR.
LSR[4]: Receive Break Flag
Logic 0 = No break condition (default).
Logic 1 = The receiver received a break signal (RX was a logic 0 for at least one character frame time). In the
FIFO mode, only one break character is loaded into the FIFO. The break indication remains until the RX
input returns to the idle condition, “mark” or logic 1. If the LSR interrupt is enabled (IER bit-2), an interrupt will
be generated when the character is in the RHR.
LSR[5]: Transmit Holding Register Empty Flag
This bit is the Transmit Holding Register Empty indicator. This bit indicates that the transmitter is ready to
accept a new character for transmission. In addition, this bit causes the UART to issue an interrupt to the host
when the THR interrupt enable is set. The THR bit is set to a logic 1 when the last data byte is transferred from
the transmit holding register to the transmit shift register. The bit is reset to logic 0 concurrently with the data
loading to the transmit holding register by the host. In the FIFO mode this bit is set when the transmit FIFO is
empty, it is cleared when the transmit FIFO contains at least 1 byte.
LSR[6]: THR and TSR Empty Flag
相關PDF資料
PDF描述
ATMEGA168-15MT1 MCU AVR 16K FLASH 15MHZ 32-QFN
ATMEGA168-15MT MCU AVR 16K FLASH 15MHZ 32-QFN
ST16C1450IQ48-F IC UART FIFO 1B 48TQFP
XR68M752IL32-F IC UART FIFO 64B DUAL 32QFN
XR16M752IL32-F IC UART FIFO 64B DUAL 32QFN
相關代理商/技術參數
參數描述
ST16C2550IJ44 制造商:Exar Corporation 功能描述:
ST16C2550IJ44-F 功能描述:UART 接口集成電路 DUAL UART W/16BYTE FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
ST16C2550IJ44TR-F 制造商:Exar Corporation 功能描述:UART 2-CH 16Byte FIFO 3.3V/5V 44-Pin PLCC T/R 制造商:Exar Corporation 功能描述:ST16C2550IJ44TR-F
ST16C2550IP40 功能描述:UART 接口集成電路 DUAL UART W/16 BYTE FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
ST16C2550IQ48 制造商:Rochester Electronics LLC 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*