參數資料
型號： SST89E54RC-33-C-NJE
元件分類： 微控制器/微處理器
英文描述： 8-BIT, FLASH, 33 MHz, MICROCONTROLLER, PQCC44
封裝： ROHS COMPLIANT, PLASTIC, MS-018AC, LCC-44
文件頁數： 42/57頁
文件大?。?/td> 652K
代理商： SST89E54RC-33-C-NJE
Data Sheet
FlashFlex MCU
SST89E52RC / SST89E54RC
47
2007 Silicon Storage Technology, Inc.
S71259-04-000
1/07
12.1 DC Electrical Characteristics
TABLE
12-6: DC Characteristics for SST89E5xRC: TA = -0°C to +70°C; VDD = 4.5-5.5V; VSS = 0V
Symbol
Parameter
Test Conditions
Min
Max
Units
VIL
Input Low Voltage
4.5 < VDD < 5.5
-0.5
0.2VDD - 0.1
V
VIH
Input High Voltage
4.5 < VDD < 5.5
0.2VDD + 0.9
VDD + 0.5
V
VIH1
Input High Voltage (XTAL1, RST)
4.5 < VDD < 5.5
0.7VDD
VDD + 0.5
V
VOL
Output Low Voltage (Ports 1.5, 1.6, 1.7)
VDD = 4.5V
IOL = 16mA
1.0
V
VOL
Output Low Voltage (Ports 1, 2, 3)1
1. Under steady state (non-transient) conditions, IOL must be externally limited as follows:
Maximum IOL per port pin:
15mA
Maximum IOL per 8-bit port:
26mA
Maximum IOL total for all outputs:71mA
If IOL exceeds the test condition, VOL may exceed the related specification.
Pins are not guaranteed to sink current greater than the listed test conditions.
VDD = 4.5V
IOL = 100A2
2. Capacitive loading on Ports 0 and 2 may cause spurious noise to be superimposed on the VOLs of ALE and Ports 1 and 3. The noise
due to external bus capacitance discharging into the Port 0 and 2 pins when the pins make 1-to-0 transitions during bus operations.
In the worst cases (capacitive loading > 100pF), the noise pulse on the ALE pin may exceed 0.8V. In such cases, it may be desirable
to qualify ALE with a Schmitt Trigger, or use an address latch with a Schmitt Trigger STROBE input.
0.3
V
IOL = 1.6mA2
0.45
V
IOL = 3.5mA2
1.0
V
VOL1
Output Low Voltage (Port 0, ALE, PSEN#)1,3
3. Load capacitance for Port 0, ALE and PSEN#= 100pF, load capacitance for all other outputs = 80 pF.
VDD = 4.5V
IOL = 200A2
0.3
V
IOL = 3.2mA2
0.45
V
VOH
Output High Voltage (Ports 1, 2, 3, ALE, PSEN#)4
4. Capacitive loading on Ports 0 and 2 may cause the VOH on ALE and PSEN# to momentarily fall below the VDD - 0.7 specification
when the address bits are stabilizing.
VDD = 4.5V
IOH = -10A
VDD - 0.3
V
IOH = -30A
VDD - 0.7
V
IOH = -60A
VDD - 1.5
V
VOH1
Output High Voltage (Port 0 in External Bus Mode)4
VDD = 4.5V
IOH = -200A
VDD - 0.3
V
IOH = -3.2mA
VDD - 0.7
V
IIL
Logical 0 Input Current (Ports 1, 2, 3)
VIN = 0.4V
-75
A
ITL
Logical 1-to-0 Transition Current (Ports 1, 2, 3)5
5. Pins of Ports 1, 2, and 3 source a transition current when they are being externally driven from 1 to 0. The transition current reaches
its maximum value when VIN is approximately 2V.
VIN = 2V
-650
A
ILI
Input Leakage Current (Port 0)
0.45 < VIN < VDD-0.3
±10
A
RRST
RST Pull-down Resistor
40
225
K
Ω
CIO
Pin Capacitance6
6. Pin capacitance is characterized but not tested. EA# is 25pF (max).
@ 1 MHz, 25°C
15
pF
IDD
Power Supply Current
Active Mode @ 33 MHz
32
mA
Idle Mode@ 33 MHz
26
mA
Power-down Mode (min VDD = 2V)
TA = 0°C to 70°C
50
A
T12-6.1 1259
相關PDF資料
PDF描述
SST89E52RC-33-C-NJE 8-BIT, FLASH, 33 MHz, MICROCONTROLLER, PQCC44
SST89E52RC-33-C-PIE 8-BIT, FLASH, 33 MHz, MICROCONTROLLER, PDIP40
SST89V516RD-33-I-PIE 8-BIT, FLASH, 33 MHz, MICROCONTROLLER, PDIP40
SST89V516RD-33-C-PI 8-BIT, FLASH, 33 MHz, MICROCONTROLLER, PDIP40
SST89V516RD-33-I-PIE 8-BIT, FLASH, 33 MHz, MICROCONTROLLER, PDIP40
相關代理商/技術參數
參數描述
SST89E54RC-33-C-PIE 功能描述:8位微控制器 -MCU 8-Bit 16K+1K Flash 33MHz 3/16-Bit Timer RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
SST89E54RD 制造商:SST 制造商全稱:Silicon Storage Technology, Inc 功能描述:FlashFlex MCU
SST89E54RD2 制造商:SST 制造商全稱:Silicon Storage Technology, Inc 功能描述:FlashFlex51 MCU
SST89E54RD2/RD 制造商:SST 制造商全稱:Silicon Storage Technology, Inc 功能描述:FlashFlex51 MCU
SST89E54RD2-33-C-NI 制造商:SST 制造商全稱:Silicon Storage Technology, Inc 功能描述:FlashFlex51 MCU
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*