- 您現在的位置：買賣IC網 > PDF目錄10518 > SSM2518CBZ-R7 (Analog Devices Inc)IC AMP AUD PWR 2W STER D 16WLCSP PDF資料下載
參數資料
| 型號： | SSM2518CBZ-R7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 15/48頁 |
| 文件大小： | 0K |
| 描述： | IC AMP AUD PWR 2W STER D 16WLCSP |
| 產品變化通告： | 8mm Carrier Tape Changes 28/Feb/2012 |
| 標準包裝： | 1 |
| 類型： | D 類 |
| 輸出類型： | 2 通道（立體聲） |
| 在某負載時最大輸出功率 x 通道數量： | 2.5W x 2 @ 4 歐姆 |
| 電源電壓： | 2.5 V ~ 5.5 V |
| 特點： | 消除爆音，數字輸入，I²C，I²S，靜音，短路和熱保護，關機，音量控制 |
| 安裝類型： | 表面貼裝 |
| 供應商設備封裝： | 16-WLCSP（2.21x2.21） |
| 封裝/外殼： | 16-WFBGA，WLCSP |
| 包裝： | 剪切帶 (CT) |
| 其它名稱： | SSM2518CBZ-R7CT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
SSM2518
Data Sheet
Rev. A | Page 22 of 48
I2C CONFIGURATION INTERFACE
OVERVIEW
processor bus driving multiple peripherals. Two pins, serial data
(SDA) and serial clock (SCL), carry information between the
is always a slave on the bus, meaning it cannot initiate a data
transfer. Each slave device is recognized by a unique device
address. The device address byte format is shown in Figure 31.
The address resides in the first seven bits of the I2C write. The
LSB of this byte sets either a read or write operation.
Logic Level 1 corresponds to a read operation, and Logic Level 0
corresponds to a write operation. The full byte addresses are
shown in Figure 3, where the subaddresses are automatically
incremented at word boundaries and can be used for writing
large amounts of data to contiguous memory locations. This
increment happens automatically after a single word write
unless a stop condition is encountered. A data transfer is always
terminated by a stop condition.
Both SDA and SCL should have a 2.2 kΩ pull-up resistor on the
lines connected to them.
BIT 0
BIT 1
BIT 2
BIT 3
BIT 4
BIT 5
BIT 6
BIT 7
01
101
ADDR
0
R/W
10
242-
033
Figure 31. I2C Device Address Byte Format
Addressing
Initially, each device on the I2C bus is in an idle state,
monitoring the SDA and SCL lines for a start condition and
the proper address. The I2C master initiates a data transfer by
establishing a start condition, defined by a high-to-low transition
on SDA while SCL remains high. This indicates that an
address/data stream follows. All devices on the bus respond to
the start condition and shift the next eight bits (the 7-bit
address plus the R/W bit) MSB first. The device that recognizes
the transmitted address responds by pulling the data line low
during the ninth clock pulse. The device address is determined
by the state of the ADDR pin. This ninth bit is known as an
acknowledge bit. All other devices withdraw from the bus at
this point and return to the idle condition. The R/W bit
determines the direction of the data. A Logic 0 on the LSB of
the first byte means that the master writes information to the
peripheral, whereas a Logic 1 means that the master reads
information from the peripheral after writing the subaddress
and repeating the start address. A data transfer takes place until
a stop condition is encountered. A stop condition occurs when
SDA transitions from low to high while SCL is held high. The
timing for the I2C port is shown in
Stop and start conditions can be detected at any stage during the
data transfer. If these conditions are asserted out of sequence with
normal read and write operations, the SSM2518 immediately
jumps to the idle condition. During a given SCL high period,
the user should issue only one start condition, one stop condition,
or a single stop condition followed by a single start condition. If
an invalid subaddress is issued by the user, the SSM2518 does
not issue an acknowledge and returns to the idle condition. If
the user exceeds the highest subaddress while in auto-increment
mode, one of two actions is taken. In read mode, the SSM2518
outputs the highest subaddress register contents until the master
device issues a no acknowledge, indicating the end of a read. A
no acknowledge condition is where the SDA line is not pulled
low on the ninth clock pulse of SCL. If the highest subaddress
location is reached while in write mode, the data for the invalid
byte is not loaded into any subaddress register, a no acknowledge
is issued by the SSM2518, and the part returns to the idle
condition.
I2C Read and Write Operations
Figure 33 shows the timing of a single word write operation.
Every ninth clock, the SSM2518 issues an acknowledge by
pulling SDA low.
Figure 34 shows the timing of a burst mode write sequence.
This figure shows an example where the target destination
registers are two bytes. The SSM2518 knows to increment its
subaddress register every byte because the requested subaddress
corresponds to a register or memory area with a byte word
length.
The timing of a single word read operation is shown in
Figure 35. Note that the first R/W bit is 0, indicating a write
operation. This is because the subaddress still needs to be
written to set up the internal address. After the
acknowledges the receipt of the subaddress, the master must
issue a repeated start command followed by the chip address
byte with the R/
W bit set to 1 (read). This causes the
SDA to reverse and begin driving data back to the master. The
master then responds every ninth pulse with an acknowledge
pulse to the
.
Figure 36 shows the timing of a burst mode read sequence. This
figure shows an example where the target destination registers
are two bytes. The SSM2518 knows to increment its subaddress
register every byte because the requested subaddress corresponds
to a register or memory area with a byte word length.
相關PDF資料 |
PDF描述 |
|---|---|
| LTC2368CMS-18#PBF | IC ADC 18BIT SPI/SRL 1M 16MSOP |
| UP050B750K-A-B | CAP CER 75PF 50V 10% AXIAL |
| LTC2380CDE-16#PBF | IC ADC 16BIT 2MSPS 16DFN |
| UP050B681K-NAC | CAP CER 680PF 50V 10% AXIAL |
| LTC2380CMS-16#PBF | IC ADC 16BIT 2MSPS 16-MSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SSM2518CBZ-RL | 功能描述:IC AMP AUD PWR 2C STER D 16WLCSP RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:D 類 輸出類型:1-通道（單聲道），帶立體聲耳機 在某負載時最大輸出功率 x 通道數量:930mW x 1 @ 8 歐姆; 40mW x 2 @ 16 歐姆 電源電壓:2.7 V ~ 5.5 V 特點:消除爆音，差分輸入，I²C，靜音，關閉，音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP（2.09x2.09） 封裝/外殼:25-WFBGA，WLCSP 包裝:帶卷 (TR) 其它名稱:MAX97000EWA+T-ND |
| SSM2518CPZ | 功能描述:IC AMP AUD PWR 2C STER D 20LFCSP RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:D 類 輸出類型:1-通道（單聲道），帶立體聲耳機 在某負載時最大輸出功率 x 通道數量:930mW x 1 @ 8 歐姆; 40mW x 2 @ 16 歐姆 電源電壓:2.7 V ~ 5.5 V 特點:消除爆音，差分輸入，I²C，靜音，關閉，音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP（2.09x2.09） 封裝/外殼:25-WFBGA，WLCSP 包裝:帶卷 (TR) 其它名稱:MAX97000EWA+T-ND |
| SSM2518CPZ-R7 | 功能描述:IC AMP AUD PWR 2C STER D 20LFCSP RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:D 類 輸出類型:1-通道（單聲道），帶立體聲耳機 在某負載時最大輸出功率 x 通道數量:930mW x 1 @ 8 歐姆; 40mW x 2 @ 16 歐姆 電源電壓:2.7 V ~ 5.5 V 特點:消除爆音，差分輸入，I²C，靜音，關閉，音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP（2.09x2.09） 封裝/外殼:25-WFBGA，WLCSP 包裝:帶卷 (TR) 其它名稱:MAX97000EWA+T-ND |
| SSM2518CPZ-RL | 功能描述:IC AMP AUD PWR 2C STER D 20LFCSP RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:D 類 輸出類型:1-通道（單聲道），帶立體聲耳機 在某負載時最大輸出功率 x 通道數量:930mW x 1 @ 8 歐姆; 40mW x 2 @ 16 歐姆 電源電壓:2.7 V ~ 5.5 V 特點:消除爆音，差分輸入，I²C，靜音，關閉，音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP（2.09x2.09） 封裝/外殼:25-WFBGA，WLCSP 包裝:帶卷 (TR) 其它名稱:MAX97000EWA+T-ND |
| SSM2519ACBZ-R7 | 功能描述:音頻放大器 Digital PDM Filterless Class D Mono Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。