- 您現在的位置：買賣IC網 > PDF目錄10401 > SSM2306CPZ-REEL7 (Analog Devices Inc)IC AMP AUDIO 2.4W STER D 16LFCSP PDF資料下載
參數資料
| 型號： | SSM2306CPZ-REEL7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 4/16頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC AMP AUDIO 2.4W STER D 16LFCSP |
| 設計資源： | Analog Audio Input, Class-D Output with ADAU1701, SSM2306, and ADP3336 (CN0162) |
| 標準包裝： | 1 |
| 類型： | D 類 |
| 輸出類型： | 2 通道（立體聲） |
| 在某負載時最大輸出功率 x 通道數量： | 2.4W x 2 @ 4 歐姆 |
| 電源電壓： | 2.5 V ~ 5 V |
| 特點： | 消除爆音，差分輸入，短路和熱保護，關閉 |
| 安裝類型： | 表面貼裝 |
| 供應商設備封裝： | 16-LFCSP-VQ |
| 封裝/外殼： | 16-VFQFN 裸露焊盤，CSP |
| 包裝： | 標準包裝 |
| 產品目錄頁面： | 764 (CN2011-ZH PDF) |
| 配用： | SSM2306-MINI-EVALZ-ND - BOARD EVAL FOR SSM2306-MINI SSM2306-EVALZ-ND - BOARD EVAL FOR SSM2306 |
| 其它名稱： | SSM2306CPZ-REEL7DKR |
SSM2306
Rev. 0 | Page 12 of 16
APPLICATION NOTES
OVERVIEW
The SSM2306 stereo, Class-D, audio amplifier features a filterless
modulation scheme that greatly reduces the external compo-
nents count, conserving board space and, thus, reducing systems
cost. The SSM2306 does not require an output filter; instead, it
relies on the inherent inductance of the speaker coil and the
natural filtering capacity of the speaker and human ear to fully
recover the audio component of the square wave output.
Although most Class-D amplifiers use some variation of pulse-
width modulation (PWM), the SSM2306 uses sigma-delta (Σ-Δ)
modulation to determine the switching pattern of the output
devices. This provides a number of important benefits. Σ-Δ
modulators do not produce a sharp peak with many harmonics
in the AM frequency band, as pulse-width modulators often do.
Σ-Δ modulation provides the benefits of reducing the amplitude
of spectral components at high frequencies; that is, reducing EMI
emission that might otherwise radiate by the use of speakers
and long cable traces. The SSM2306 also offers protection
circuits for overcurrent and overtemperature protection.
GAIN SELECTION
The SSM2306 has a pair of internal resistors that set an 18 dB
default gain for the amplifier. It is possible to adjust the SSM2306
gain by using external resistors at the input. To set a gain lower
than 18 dB, refer to Figure 32 for the differential input configu-
ration and Figure 33 for the single-ended configuration. Calculate
the external gain configuration as
External Gain Settings = 344 kΩ/(43 kΩ + REXT)
POP-AND-CLICK SUPPRESSION
Voltage transients at the output of audio amplifiers can occur with
the activation or deactivation of shutdown. Furthermore, voltage
transients as low as 10 mV are audible as an audio pop in the
speaker. Likewise, clicks and pops are classified as undesirable
audible transients generated by the amplifier system, and as
such, as not coming from the system input signal. These types
of transients generate when the amplifier system changes its
operating mode. For example, the following can be sources of
audible transients:
System power-up/power-down
Mute/unmute
Input source change
Sample rate change
The SSM2306 has a pop-and-click suppression architecture that
reduces these output transients, resulting in noiseless activation and
deactivation.
EMI NOISE
The SSM2306 uses a proprietary modulation and spread-
spectrum technology to minimize EMI emissions from the
device. Figure 34 shows SSM2306 EMI emission starting from
100 kHz to 30 MHz. Figure 35 shows SSM2306 EMI emission
from 30 kHz to 2 GHz. These figures clearly depict the SSM2306
EMI behavior as being well below the FCC regulation values,
starting from 100 kHz and passing beyond 1 GHz of frequency.
Although the overall EMI noise floor is slightly higher, frequency
spurs from the SSM2306 are greatly reduced.
70
0
0.1
100
FREQUENCY (MHz)
L
E
VE
L
(d
B
(
V
/m
))
60
50
40
30
20
10
110
= HORIZONTAL
= VERTICAL
= REGULATION VALUE
06
54
2-
0
39
Figure 34. EMI Emissions from SSM2306
70
0
10
10k
FREQUENCY (MHz)
L
E
VE
L
(d
B
(
V
/m
))
60
50
40
30
20
10
100
1k
= HORIZONTAL
= VERTICAL
= REGULATION VALUE
06
54
2-
0
40
Figure 35. EMI Emissions from SSM2306
a 1 kHz input signal, producing 0.5 W output power into an 8 Ω
load from a 3.6 V supply. Cable length was approximately 5 cm.
To detect EMI, a magnetic probe was used touching the 2-inch
output trace to the load.
相關PDF資料 |
PDF描述 |
|---|---|
| VI-J71-MY-B1 | CONVERTER MOD DC/DC 12V 50W |
| VI-B1F-IV-F1 | CONVERTER MOD DC/DC 72V 150W |
| VI-J70-MY-B1 | CONVERTER MOD DC/DC 5V 50W |
| VE-26N-IW-F2 | CONVERTER MOD DC/DC 18.5V 100W |
| VI-J5K-MY-B1 | CONVERTER MOD DC/DC 40V 50W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SSM2306-EVALZ | 功能描述:BOARD EVAL FOR SSM2306 RoHS:是 類別:編程器，開發系統 >> 評估板 - 音頻放大器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- |
| SSM2306-MINI-EVALZ | 功能描述:BOARD EVAL FOR SSM2306-MINI RoHS:是 類別:編程器，開發系統 >> 評估板 - 音頻放大器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- |
| SSM2306N | 制造商:SSC 制造商全稱:Silicon Standard Corp. 功能描述:N-CHANNEL ENHANCEMENT-MODE POWER MOSFET |
| SSM2307GN | 制造商:SSC 制造商全稱:Silicon Standard Corp. 功能描述:P-CHANNEL ENHANCEMENT MODE POWER MOSFET |
| SSM2307N | 制造商:SSC 制造商全稱:Silicon Standard Corp. 功能描述:P-CHANNEL ENHANCEMENT MODE POWER MOSFET |
發布緊急采購，3分鐘左右您將得到回復。