- 您現在的位置：買賣IC網 > PDF目錄297468 > SS-01GL13-FD SNAP ACTING/LIMIT SWITCH, SPDT, MOMENTARY, 0.1A, 30VDC, 2mm, THROUGH HOLE-STRAIGHT PDF資料下載
參數資料
| 型號： | SS-01GL13-FD |
| 元件分類： | 開關 |
| 英文描述： | SNAP ACTING/LIMIT SWITCH, SPDT, MOMENTARY, 0.1A, 30VDC, 2mm, THROUGH HOLE-STRAIGHT |
| 封裝： | ROHS COMPLIANT |
| 文件頁數： | 9/9頁 |
| 文件大小： | 239K |
| 代理商： | SS-01GL13-FD |
9
SS
Precautions
Refer to General Information.
■ Cautions
Terminal Connection
When soldering the lead wire to the terminal, first insert the lead
wire conductor through the terminal hole and then conduct sol-
dering.
Make sure that the capacity of the soldering iron is 60 W maxi-
mum. Do not take more than 350°C for the temperature at the tip
of the soldering iron. Do not take more than 5 s to solder the
switch terminal. Improper soldering involving an excessively high
temperature or excessive soldering time may deteriorate the char-
acteristics of the Switch.
Be sure to apply only the minimum required amount of flux. The
Switch may have contact failures if flux intrudes into the interior of
the Switch.
Use the following lead wires to connect to the solder terminals.
If the PCB terminal models are soldered in the solder bath, flux
will permeate inside the Switch and cause contact failure. There-
fore, manually solder the PCB terminal.
Wire the quick-connect terminals (#110) with receptacles. Insert
the terminals straight into the receptacles. Do not impose exces-
sive force on the terminal in the horizontal direction, otherwise the
terminal may be deformed or the housing may be damaged.
Insulation Distance
According to EN61058-1, the minimum insulation thickness for
this Switch should be 1.1 mm and minimum clearance distance
between the terminal and mounting plate should be 1.6 mm. If the
insulation distance cannot be provided in the product incorporat-
ing the Switch, either use a Switch with insulation barrier or use a
Separator to ensure sufficient insulation distance. Refer to Sepa-
rator.
■ Correct Use
Mounting
Turn OFF the power supply before mounting or removing the
Switch, wiring, or performing maintenance or inspection. Failure
to do so may result in electric shock or burning.
Use M2.3 mounting screws with plane washers or spring washers
to securely mount the Switch. Tighten the screws to a torque of
0.23 to 0.26 Nm {2.3 to 2.7 kgfcm}.
Mount the Switch onto a flat surface. Mounting on an uneven sur-
face may cause deformation of the Switch, resulting in faulty oper-
ation or breakage in the housing.
Operating Stroke Setting
Take particular care in setting the operating stroke for the pin
plunger models. Make sure that the operating stroke is 70% to
100% of the rated OT distance. Do not operate the actuator
exceeding the OT distance, otherwise the durability of the Switch
may be shortened.
Using Micro Loads
Using a model for ordinary loads to open or close the contact of a
micro load circuit may result in faulty contact. Use models that
operate in the following range. However, even when using micro
load models within the operating range shown below, if inrush
current occurs when the contact is opened or closed, it may
increase contact wear and so decrease durability. Therefore,
insert a contact protection circuit where necessary.
The minimum applicable load is the N-level reference value. This
value indicates the malfunction reference level for the reliability
level of 60% (
λ 60). The equation, λ 60 = 0.5×10–6/operations
indicates that the estimated malfunction rate is less than 1/
2,000,000 operations with a reliability level of 60%.
■ Separators
Note:
The material is EAVTC (Epoxide Alkyd Varnished Tetron
Cloth) and its heat-resisting temperature is 130
°C.
■ Connector
Refer to Terminal Connectors.
Model
Conductor size
SS-5
0.5 to 0.75 mm2
SS-10
0.75 mm2
Applicable
Switch
Thickness (mm)
Model (see note)
SS, D2S, D2SW
0.18
Separator for SS0.18
0.4
Separator for SS0.4
Operating range
for micro load
models SS-01
Operating
range for
general-load
models
SS-5, SS-10
Current (mA)
Inoperable
range
V
oltage
(V)
Separator
Separator for SS
@
ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.
To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.
Cat. No. B032-E1-12
相關PDF資料 |
PDF描述 |
|---|---|
| SS-60000-014 | 8 CONTACT(S), FEMALE, 47.5 DEGREE TELECOM AND DATACOM CONNECTOR, SOLDER, JACK |
| SS-6488S-A-NF-01-50 | 8 CONTACT(S), FEMALE, RIGHT ANGLE TELECOM AND DATACOM CONNECTOR, SOLDER, JACK |
| SS-6488S-A-NF-01 | 8 CONTACT(S), FEMALE, RIGHT ANGLE TELECOM AND DATACOM CONNECTOR, SOLDER, JACK |
| SS-6488S-A-PG4-BA-RMK4-50 | 8 CONTACT(S), FEMALE, TELECOM AND DATACOM CONNECTOR, SOLDER |
| SS-6588-02-NF-K1-HT-50 | 8 CONTACT(S), FEMALE, STRAIGHT TELECOM AND DATACOM CONNECTOR, SOLDER, JACK |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SS01GL13FT | 制造商:Omron Electronic Components LLC 功能描述:SWIT SA NO/NC SPDT SIMULATED ER LVR QC 0.1A 125VAC 30VDC 0.1 - Trays 制造商:Omron Electronic Components LLC 功能描述:SWITCH SIM ROLLER SPDT .1A .110 制造商:Omron Electronic Components LLC 功能描述:Switch Snap Action N.O./N.C. SPDT Simulated Roller Lever Quick Connect 0.1A 125VAC 30VDC 0.16N Screw Mount |
| SS-01GL13-FT | 功能描述:基本/快動開關 Subminiature Basic Switch RoHS:否 制造商:Omron Electronics 觸點形式:SPDT 執行器:Lever 電流額定值:5 A 電壓額定值 AC:250 V 電壓額定值 DC:30 V 功率額定值: 工作力:120 g IP 等級:IP 67 NEMA 額定值: 端接類型:Wire 安裝:Panel |
| SS01GL13P | 制造商:Omron Electronic Components LLC 功能描述:SWIT SA NO/NC SPDT SIMULATED ER LVR SLDR 0.1A 125VAC 30VDC 0 - Trays 制造商:Omron Electronic Components LLC 功能描述:SWITCH SIM ROLLER SPDT .1A SLDR |
| SS-01GL13P | 功能描述:基本/快動開關 0.1A Sim rollr lever Solder terminals RoHS:否 制造商:Omron Electronics 觸點形式:SPDT 執行器:Lever 電流額定值:5 A 電壓額定值 AC:250 V 電壓額定值 DC:30 V 功率額定值: 工作力:120 g IP 等級:IP 67 NEMA 額定值: 端接類型:Wire 安裝:Panel |
| SS01GL13PB | 制造商:Omron Electronic Components LLC 功能描述:SWIT SA NO/NC SPDT SIMULATED ER LVR PC PINS 0.1A 125VAC 30VD - Trays 制造商:Omron Electronic Components LLC 功能描述:SWITCH SIM ROLLER SPDT 0.1A PCB |
發布緊急采購，3分鐘左右您將得到回復。