- 您現在的位置：買賣IC網 > PDF目錄297432 > SQE48T40025-NDB0 (POWER-ONE INC) 1-OUTPUT DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | SQE48T40025-NDB0 |
| 廠商： | POWER-ONE INC |
| 元件分類： | 電源模塊 |
| 英文描述： | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| 封裝： | ROHS COMPLIANT, ONE-EIGHTH BRICK PACKAGE-8 |
| 文件頁數： | 9/13頁 |
| 文件大?。?/td> | 764K |
| 代理商： | SQE48T40025-NDB0 |
SQE48T40025 DC-DC Converter
36-75 VDC Input; 2.5 VDC @ 40 A Output
Preliminary Data Sheet
Operations
Input and Output Impedance
These power converters have been designed to be
stable with no external capacitors when used in low
inductance input and output circuits.
However, in some applications, the inductance
associated with the distribution from the power
source to the input of the converter can affect the
stability of the converter. A 33 F electrolytic
capacitor with an ESR < 1 across the input is
required to ensure proper operation of the converter
over wide range of input source impedance and
transients.
In many applications, the user has to use decoupling
capacitance at the load. The power converter will
exhibit
stable
operation
with
external
load
capacitance up to 10,000 F.
ON/OFF (Pin 2)
The ON/OFF pin is used to turn the power converter
on or off remotely via a system signal. There are two
remote control options available, positive and
negative logic, with both referenced to Vin(-). A
typical connection is shown in Fig. A.
Rload
Vin
CONTROL
INPUT
Vin (+)
Vin (-)
ON/OFF
Vout (+)
Vout (-)
TRIM
SENSE (+)
SENSE (-)
(Top View)
SQE48 Converter
Fig. A: Circuit configuration for ON/OFF function.
The positive logic version turns on when the ON/OFF
pin is at a logic high and turns off when the pin is at a
logic low. The converter is on when the ON/OFF pin
is left open. See the Electrical Specifications for logic
high/low definitions.
The negative logic version turns on when the pin is
at a logic low and turns off when the pin is at a logic
high. The ON/OFF pin can be hard wired directly to
Vin(-) to enable automatic power up of the converter
without the need of an external control signal.
The ON/OFF pin is internally pulled up to 5 V
through
a
resistor.
A
properly
de-bounced
mechanical switch, open-collector transistor, or FET
can be used to drive the input of the ON/OFF pin.
The device must be capable of sinking up to 0.2 mA
at a low level voltage of
≤ 0.8 V. An external voltage
source (±20 V maximum) may be connected directly
to the ON/OFF input, in which case it must be
capable of sourcing or sinking up to 1 mA depending
on the signal polarity. See the Startup Information
section for system timing waveforms associated with
use of the ON/OFF pin.
Remote Sense (Pins 5 and 7)
The remote sense feature of the converter
compensates for voltage drops occurring between
the output pins of the converter and the load. The
SENSE(-) (Pin 5) and SENSE(+) (Pin 7) pins should
be connected at the load or at the point where
regulation is required (see Fig. B).
100
10
Rw
Rload
Vin
Vin (+)
Vin (-)
ON/OFF
Vout (+)
Vout (-)
TRIM
SENSE (+)
SENSE (-)
(Top View)
SQE48 Converter
Fig. B: Remote sense circuit configuration.
CAUTION
If remote sensing is not utilized, the SENSE(-) pin must be
connected to the Vout(-) pin (Pin 4), and the SENSE(+) pin
must be connected to the Vout(+) pin (Pin 8) to ensure the
converter will regulate at the specified output voltage. If these
connections are not made, the converter will deliver an
output voltage that is higher than the specified data sheet
value.
Because the sense leads carry minimal current,
large traces on the end-user board are not required.
However, sense traces should be run side by side
and located close to a ground plane to minimize
system noise and ensure optimum performance.
The converter’s output overvoltage protection (OVP)
senses the voltage across Vout(+) and Vout(-), and
not across the sense lines, so the resistance (and
resulting voltage drop) between the output pins of
the converter and the load should be minimized to
prevent unwanted triggering of the OVP.
When utilizing the remote sense feature, care must
be taken not to exceed the maximum allowable
output power capability of the converter, which is
equal to the product of the nominal output voltage
and the allowable output current for the given
conditions.
When using remote sense, the output voltage at the
converter can be increased by as much as 10%
above the nominal rating in order to maintain the
required voltage across the load. Therefore, the
designer must, if necessary, decrease the maximum
current (originally obtained from the derating curves)
ZD-01723 Rev 1.1
www.power-one.com
Page 5 of 13
相關PDF資料 |
PDF描述 |
|---|---|
| SR3050PT | 15 A, 50 V, SILICON, RECTIFIER DIODE, TO-247AD |
| SR3020PT | 15 A, 20 V, SILICON, RECTIFIER DIODE, TO-247AD |
| SR305AA100D | FEMALE, STRAIGHT TWO PART BOARD CONNECTOR, WIRE WRAP, SOCKET |
| SR305AA100U | FEMALE, STRAIGHT TWO PART BOARD CONNECTOR, WIRE WRAP, SOCKET |
| SR305AA30D | FEMALE, STRAIGHT TWO PART BOARD CONNECTOR, WIRE WRAP, SOCKET |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SQE48T50012-NDA0 | 功能描述:DC/DC轉換器 RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| SQE48T50012-NDA0G | 功能描述:DC/DC轉換器 1.2Vout 50A 1.2Vout 50A RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| SQE5-P | 制造商:Power-One 功能描述: |
| SQETHERNET | 制造商:Intel 功能描述: |
| SQF620001 | 功能描述:OSC 156.25MHZ 3.3V HCSL SMD RoHS:是 類別:晶體和振蕩器 >> 振蕩器 系列:SaRonix-eCera™ SQ 標準包裝:1 系列:VG-4512CA 類型:VCXO 頻率:153.6MHz 功能:三態（輸出啟用） 輸出:LVPECL 電源電壓:3.3V 頻率穩定性:- 工作溫度:-40°C ~ 85°C 電流 - 電源（最大）:60mA 額定值:- 安裝類型:表面貼裝 尺寸/尺寸:0.276" L x 0.197" W（7.00mm x 5.00mm） 高度:0.071"（1.80mm） 封裝/外殼:6-SMD，無引線（DFN，LCC） 包裝:Digi-Reel® 電流 - 電源（禁用）（最大）:- 其它名稱:SER3790DKR |
發布緊急采購，3分鐘左右您將得到回復。