- 您現在的位置：買賣IC網 > PDF目錄297430 > SQ24T10015-PCCSG (POWER-ONE INC) 1-OUTPUT 50 W DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | SQ24T10015-PCCSG |
| 廠商： | POWER-ONE INC |
| 元件分類： | 電源模塊 |
| 英文描述： | 1-OUTPUT 50 W DC-DC REG PWR SUPPLY MODULE |
| 封裝： | ROHS COMPLIANT, ONE-EIGHTH BRICK PACKAGE-8 |
| 文件頁數： | 56/70頁 |
| 文件大?。?/td> | 933K |
| 代理商： | SQ24T10015-PCCSG |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁當前第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁
AUG 25, 2006 revised to MAR 19, 2007
Page 6 of 70
www.power-one.com
SQ24 Series DC-DC Converter Data Sheet
18-36 VDC Input; Standard Outputs from 1-12 VDC
Test Conditions
All data presented were taken with the converter soldered to
a test board, specifically a 0.060” thick printed wiring board
(PWB) with four layers. The top and bottom layers were not
metalized. The two inner layers, comprising two-ounce
copper, were used to provide traces for connectivity to the
converter.
The lack of metalization on the outer layers as well as the
limited thermal connection ensured that heat transfer from
the converter to the PWB was minimized. This provides a
worst-case but consistent scenario for thermal derating
purposes.
All measurements requiring airflow were made in vertical
and horizontal wind tunnel facilities using Infrared (IR)
thermography and thermocouples for thermometry.
Ensuring components on the converter do not exceed their
ratings is important to maintaining high reliability. If one
anticipates operating the converter at or close to the
maximum loads specified in the derating curves, it is prudent
to check actual operating temperatures in the application.
Thermographic imaging is preferable; if this capability is not
available, then thermocouples may be used. Power-One
recommends the use of AWG #40 gauge thermocouples to
ensure measurement accuracy. Careful routing of the
thermocouple leads will further minimize measurement error.
Refer to Figure H for optimum measuring thermocouple
location.
Thermal Derating
Load current vs. ambient temperature and airflow rates are
given in Fig. x.1 for through-hole version. Ambient
temperature was varied between 25 °C and 85 °C, with
airflow rates from 30 to 500 LFM (0.15 to 2.5 m/s), and
vertical and horizontal converter mounting.
For each set of conditions, the maximum load current was
defined as the lowest of:
(i) The output current at which any FET junction temperature
did not exceed a maximum specified temperature (120 °C)
as indicated by the thermographic image, or
(ii) The nominal rating of the converter (4 A on 12 V, 5.3 A
on 8.0 V, 8 A on 6.0 V, 10 A on 5.0 V, and 15 A on
3.3 – 1.0 V).
During normal operation, derating curves with maximum FET
temperature less than or equal to 120 °C should not be
exceeded. Temperature on the PCB at the thermocouple
location shown in Fig. H should not exceed 118 °C in order
to operate inside the derating curves.
Fig. H: Location of the thermocouple for thermal testing.
Efficiency
Fig. x.5 shows the efficiency vs. load current plot for ambient
temperature of 25 C, airflow rate of 300 LFM (1.5 m/s) with
vertical mounting and input voltages of 18 V, 24 V and 36 V.
Also, a plot of efficiency vs. load current, as a function of
ambient temperature with Vin = 24 V, airflow rate of 200 LFM
(1 m/s) with vertical mounting is shown in Fig. x.6.
Power Dissipation
Fig. x.7 shows the power dissipation vs. load current plot for
Ta = 25 C, airflow rate of 300 LFM (1.5 m/s) with vertical
mounting and input voltages of 18 V, 24 V and 36 V. Also, a
plot of power dissipation vs. load current, as a function of
ambient temperature with Vin = 24 V, airflow rate of 200 LFM
(1 m/s) with vertical mounting is shown in Fig. x.8.
Start-up
Output voltage waveforms, during the turn-on transient using
the ON/OFF pin for full rated load currents (resistive load)
are shown without and with external load capacitance in
Fig. x.9 and Fig. x.10, respectively.
Ripple and Noise
Fig. x.13 shows the output voltage ripple waveform,
measured at full rated load current with a 10 F tantalum
and 1 F ceramic capacitor across the output. Note that all
output voltage waveforms are measured across a 1
μF
ceramic capacitor.
The input reflected ripple current waveforms are obtained
using the test setup shown in Fig x.14. The corresponding
waveforms are shown in Fig. x.15 and Fig. x.16.
相關PDF資料 |
PDF描述 |
|---|---|
| SQ24T10018-NAC0 | 1-OUTPUT 50 W DC-DC REG PWR SUPPLY MODULE |
| SQ24T10018-PCCS | 1-OUTPUT 50 W DC-DC REG PWR SUPPLY MODULE |
| SQ24T10018-PDCSG | 1-OUTPUT 50 W DC-DC REG PWR SUPPLY MODULE |
| SQ24T10020-NCCS | 1-OUTPUT 50 W DC-DC REG PWR SUPPLY MODULE |
| SQ24T10020-PBASG | 1-OUTPUT 50 W DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SQ24T10050-NAA0 | 功能描述:DC/DC轉換器 18-36Vin 10A 5Vout RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| SQ24T10050-NAA0G | 功能描述:DC/DC轉換器 RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| SQ24T10050-NAAO | 制造商:POWER-ONE INC 功能描述:PwrSup;DC-DC Converter;Out 5VDC;In 18 to 36VDC;Thru-Hole;Open-Frame;Commercial |
| SQ24T10050-NAAP | 制造商:Power-One 功能描述:DC/DC PS SGL-OUT 5V 10A 50W 8PIN QUARTER-BRICK - Bulk |
| SQ24T10050-NAAPG | 制造商:Power-One 功能描述:DC/DC PS SGL-OUT 5V 10A 50W 8PIN QUARTER-BRICK - Bulk |
發布緊急采購，3分鐘左右您將得到回復。